Dell PowerEdge R940 EMC Installation and Service Manual - Page 161

Installing the left control panel

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 161 highlights

Steps 1. Holding the pull tab, disconnect the control panel cable from the connector on the system board. 2. Using a Torx #T30 screwdriver, remove the screws that secure the left control panel to the system. 3. Holding the control panel by its sides, remove the control panel away from the system. Figure 108. Removing left control panel Next steps Install the left control panel. Installing the left control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. Steps 1. Route the control panel cable through the side wall of the system. 2. Align the control panel with the control panel slot on the system and attach the control panel to the system. 3. Connect the control panel cable connector on the system board. 4. Using a Torx #T30 screwdriver, install the screws that secure the control panel to the system. Installing and removing system components 161

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Steps
1.
Holding the pull tab, disconnect the control panel cable from the connector on the system board.
2.
Using a Torx #T30 screwdriver, remove the screws that secure the left control panel to the system.
3.
Holding the control panel by its sides, remove the control panel away from the system.
Figure 108. Removing left control panel
Next steps
Install the left control panel
.
Installing the left control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
Steps
1.
Route the control panel cable through the side wall of the system.
2.
Align the control panel with the control panel slot on the system and attach the control panel to the system.
3.
Connect the control panel cable connector on the system board.
4.
Using a Torx #T30 screwdriver, install the screws that secure the control panel to the system.
Installing and removing system components
161