Dell PowerEdge R940 EMC Installation and Service Manual - Page 132

M.2 SSD module, Removing the M.2 SSD module

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

NOTE: This step is applicable only if you are installing the expansion cards in the slots 12 and 13 of Riser 3 (IO_RISER3) and slots 9 and 10 of Riser 2(IO_RISER2). 5. Close the PCIe card latch. Figure 81. Installing expansion card into expansion card riser Next steps 1. Install the expansion card riser. 2. Connect the cables to the expansion card. 3. Follow the procedure listed in After working inside your system on page 66. M.2 SSD module Removing the M.2 SSD module Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. 3. Remove the air shroud. 4. Remove the BOSS card. NOTE: Removing the BOSS card is similar to the procedure for removing an expansion card riser. Steps 1. Loosen the screws and lift the retention straps that secure the M.2 SSD module on the BOSS card. 2. Pull the M.2 SSD module away from the BOSS card. 132 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
NOTE:
This step is applicable only if you are installing the expansion cards in the slots 12 and 13 of Riser 3
(IO_RISER3) and slots 9 and 10 of Riser 2(IO_RISER2).
5.
Close the PCIe card latch.
Figure 81. Installing expansion card into expansion card riser
Next steps
1.
Install the expansion card riser
.
2.
Connect the cables to the expansion card.
3.
Follow the procedure listed in
After working inside your system
on page 66.
M.2 SSD module
Removing the M.2 SSD module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
3.
Remove the air shroud
.
4.
Remove the BOSS card.
NOTE:
Removing the BOSS card is similar to the procedure for
removing an expansion card riser
.
Steps
1.
Loosen the screws and lift the retention straps that secure the M.2 SSD module on the BOSS card.
2.
Pull the M.2 SSD module away from the BOSS card.
132
Installing and removing system components