Dell PowerEdge R940 EMC Installation and Service Manual - Page 136

Network daughter card, Removing the NDC

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

Figure 85. Install the NDC riser Next steps 1. Connect the cables to the NDC riser. 2. Follow the procedure listed in After working inside your system on page 66. Network daughter card Removing the NDC Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. 3. Remove the Network Daughter Card (NDC) riser. Steps 1. Using a Phillips #2 screwdriver, loosen the captive screws that secure the NDC to the NDC riser. 2. Hold the NDC by the edges on either side of the touch points, and lift to remove it from the connector on the NDC riser. 3. Slide the NDC away from the NDC riser bracket until the Ethernet connectors are clear of the slot in the NDC riser. 136 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Figure 85. Install the NDC riser
Next steps
1.
Connect the cables to the NDC riser.
2.
Follow the procedure listed in
After working inside your system
on page 66.
Network daughter card
Removing the NDC
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
3.
Remove the Network Daughter Card (NDC) riser
.
Steps
1.
Using a Phillips #2 screwdriver, loosen the captive screws that secure the NDC to the NDC riser.
2.
Hold the NDC by the edges on either side of the touch points, and lift to remove it from the connector on the NDC riser.
3.
Slide the NDC away from the NDC riser bracket until the Ethernet connectors are clear of the slot in the NDC riser.
136
Installing and removing system components