Dell PowerEdge R940 EMC Installation and Service Manual - Page 83

Installing an intrusion switch

Get Dell PowerEdge R940 PDF manuals and user guides View all Dell PowerEdge R940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

3. Press the tab on the intrusion switch cable connector and disconnect the cable connected to the intrusion switch connector (INTRUSION) on the system board. 4. Remove the cables routed through the cable routing hooks on the right side of the system. 5. Push the intrusion switch out of the intrusion switch slot. Figure 37. Removing an intrusion switch Next steps Install an intrusion switch. Installing an intrusion switch Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 65. 2. Follow the procedure listed in Before working inside your system on page 66. Steps 1. Slide the intrusion switch into the intrusion switch slot. 2. Route the cables through the cable routing hooks on the side of the system. 3. Lower the cable management bracket into the system. 4. Press the bracket and insert the tabs on the bracket into the slots on the right side of the system. 5. Connect the cable to the connector (INTRUSION) on the system board. Installing and removing system components 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
3.
Press the tab on the intrusion switch cable connector and disconnect the cable connected to the intrusion switch connector
(INTRUSION) on the system board.
4.
Remove the cables routed through the cable routing hooks on the right side of the system.
5.
Push the intrusion switch out of the intrusion switch slot.
Figure 37. Removing an intrusion switch
Next steps
Install an intrusion switch
.
Installing an intrusion switch
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 65.
2.
Follow the procedure listed in
Before working inside your system
on page 66.
Steps
1.
Slide the intrusion switch into the intrusion switch slot.
2.
Route the cables through the cable routing hooks on the side of the system.
3.
Lower the cable management bracket into the system.
4.
Press the bracket and insert the tabs on the bracket into the slots on the right side of the system.
5.
Connect the cable to the connector (INTRUSION) on the system board.
Installing and removing system components
83