Dell PowerEdge T340 EMC Installation and Service Manual - Page 56

Installing the drive into the drive carrier

Get Dell PowerEdge T340 PDF manuals and user guides View all Dell PowerEdge T340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Figure 32. Removing the drive from the drive carrier Next steps 1. Replace the drive into the drive carrier. Installing the drive into the drive carrier Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the front bezel. 4. Remove the drive carrier. CAUTION: Mixing drive carriers from other generations of PowerEdge servers is not supported. Steps 1. Insert the drive into the drive carrier with the connector end of the drive towards the back of the carrier. 2. Align the screw holes on the drive with the screws holes on the drive carrier. When aligned correctly, the back of the drive is flush with the back of the drive carrier. 3. Using a Phillips #1 screwdriver, replace the screws to secure the drive to the drive carrier. NOTE: When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-pounds. NOTE: Use the screws shipped with the drive carrier to secure the drive to the drive carrier. 56 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 32. Removing the drive from the drive carrier
Next steps
1.
Replace the drive into the drive carrier.
Installing the drive into the drive carrier
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the front bezel.
4.
Remove the drive carrier.
CAUTION:
Mixing drive carriers from other generations of PowerEdge servers is not supported.
Steps
1.
Insert the drive into the drive carrier with the connector end of the drive towards the back of the carrier.
2.
Align the screw holes on the drive with the screws holes on the drive carrier. When aligned correctly, the back of the drive is flush with
the back of the drive carrier.
3.
Using a Phillips #1 screwdriver, replace the screws to secure the drive to the drive carrier.
NOTE:
When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-pounds.
NOTE:
Use the screws shipped with the drive carrier to secure the drive to the drive carrier.
56
Installing and removing system components