Dell PowerEdge T340 EMC Installation and Service Manual - Page 65

Installing the tape drive

Get Dell PowerEdge T340 PDF manuals and user guides View all Dell PowerEdge T340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Figure 42. Removing the tape drive Next steps 1. Replace the tape drive. 2. Follow the procedure listed in After working inside your system. Installing the tape drive Prerequisites 1. Ensure that you follow the procedure listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the front bezel. 4. If applicable, remove the tape drive blank. NOTE: The procedure to remove the tape drive blank and the tape drive is similar. Steps 1. Align and slide the tape drive into the tape drive bay until it clicks into place. 2. Using the Phillips #2 screwdriver, secure the tape drive to the drive bay. 3. Connect the power and data cable connectors to the connectors on the tape drive. 4. Connect the power and data cable connectors to the backplane and the system board. NOTE: Route the cables properly to prevent them from being pinched or crimped. Installing and removing system components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 42. Removing the tape drive
Next steps
1.
Replace the tape drive.
2.
Follow the procedure listed in
After working inside your system
.
Installing the tape drive
Prerequisites
1.
Ensure that you follow the procedure listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the front bezel.
4.
If applicable,
remove the tape drive blank
.
NOTE:
The procedure to remove the tape drive blank and the tape drive is similar.
Steps
1.
Align and slide the tape drive into the tape drive bay until it clicks into place.
2.
Using the Phillips #2 screwdriver, secure the tape drive to the drive bay.
3.
Connect the power and data cable connectors to the connectors on the tape drive.
4.
Connect the power and data cable connectors to the backplane and the system board.
NOTE:
Route the cables properly to prevent them from being pinched or crimped.
Installing and removing system components
65