Dell PowerEdge T340 EMC Installation and Service Manual - Page 81

M.2 SSD module, Removing the M.2 SSD module

Get Dell PowerEdge T340 PDF manuals and user guides View all Dell PowerEdge T340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Figure 59. Installing the filler bracket 6. Connect the data cables to the expansion card. Next steps 1. Install the air shroud. 2. Connect the cables to the expansion card. 3. Follow the procedure listed in After working inside your system. M.2 SSD module Removing the M.2 SSD module Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. 4. Remove the BOSS card. NOTE: The procedure to remove the BOSS card is similar to removing an expansion card. Steps 1. Using the Phillips #1 screwdriver, remove the screws securing the M.2 SSD module to the BOSS card. 2. Pull the M.2 SSD module to disconnect from the BOSS card connector. Installing and removing system components 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 59. Installing the filler bracket
6.
Connect the data cables to the expansion card.
Next steps
1.
Install the air shroud.
2.
Connect the cables to the expansion card.
3.
Follow the procedure listed in
After working inside your system
.
M.2 SSD module
Removing the M.2 SSD module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud.
4.
Remove the BOSS card.
NOTE:
The procedure to remove the BOSS card is similar to removing an expansion card.
Steps
1.
Using the Phillips #1 screwdriver, remove the screws securing the M.2 SSD module to the BOSS card.
2.
Pull the M.2 SSD module to disconnect from the BOSS card connector.
Installing and removing system components
81