Dell PowerEdge T340 EMC Installation and Service Manual - Page 86

Processor and heat sink, Removing the heat sink

Get Dell PowerEdge T340 PDF manuals and user guides View all Dell PowerEdge T340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Figure 64. Installing the MicroSD card Next steps 1. Install the IDSDM or vFlash module. 2. Follow the procedure listed in the After working inside your system. Processor and heat sink Removing the heat sink Prerequisites WARNING: The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to cool before removing it. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud Steps 1. Using a Phillips #2 screwdriver, loosen the screws on the heat sink in the order below: a. Loosen the first screw three turns. b. Loosen the second screw completely. c. Return to the first screw and loosen it completely. 2. Repeat the procedure for the remaining screws. 3. Lift the heat sink from the system. 86 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 64. Installing the MicroSD card
Next steps
1.
Install the IDSDM or vFlash module.
2.
Follow the procedure listed in the
After working inside your system
.
Processor and heat sink
Removing the heat sink
Prerequisites
WARNING:
The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to
cool before removing it.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud
Steps
1.
Using a Phillips #2 screwdriver, loosen the screws on the heat sink in the order below:
a.
Loosen the first screw three turns.
b.
Loosen the second screw completely.
c.
Return to the first screw and loosen it completely.
2.
Repeat the procedure for the remaining screws.
3.
Lift the heat sink from the system.
86
Installing and removing system components