Dell PowerEdge T340 EMC Installation and Service Manual - Page 95

Power interposer board, Removing the power interposer board

Get Dell PowerEdge T340 PDF manuals and user guides View all Dell PowerEdge T340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Figure 75. Installing a cabled power supply unit Next steps 1. Follow the procedure listed in After working inside your system. Power interposer board Removing the power interposer board Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the power supply units (PSUs). CAUTION: To prevent damage to the power interposer board, you must remove the power supply units or PSU blank from the system before removing the power interposer board (PIB). Steps 1. Disconnect all cables connected from the power interposer board (PIB) to the system board, and remove the cables from the cable retention brackets. NOTE: Observe the routing of the cable as you remove it from the system. Route the cable properly when you replace it to prevent the cable from being pinched or crimped. 2. Pressing the release latch on the PIB, lift the PIB to release it from the hooks on the PSU cage. 3. Lift the board and slide it out at an angle to disengage the guide pins on the board. Installing and removing system components 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 75. Installing a cabled power supply unit
Next steps
1.
Follow the procedure listed in
After working inside your system
.
Power interposer board
Removing the power interposer board
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the power supply units (PSUs).
CAUTION:
To prevent damage to the power interposer board, you must remove the power supply units or PSU blank
from the system before removing the power interposer board (PIB).
Steps
1.
Disconnect all cables connected from the power interposer board (PIB) to the system board, and remove the cables from the cable
retention brackets.
NOTE:
Observe the routing of the cable as you remove it from the system. Route the cable properly when you
replace it to prevent the cable from being pinched or crimped.
2.
Pressing the release latch on the PIB, lift the PIB to release it from the hooks on the PSU cage.
3.
Lift the board and slide it out at an angle to disengage the guide pins on the board.
Installing and removing system components
95