Dell PowerEdge T340 EMC Installation and Service Manual - Page 75

Cooling fan, Removing the internal cooling fan

Get Dell PowerEdge T340 PDF manuals and user guides View all Dell PowerEdge T340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

NOTE: The memory module socket has an alignment key that enables you to install the memory module in the socket in only one orientation. 4. Press the memory module with your thumbs until the ejectors firmly click into place. Figure 53. Installing a memory module Next steps 1. Install the air shroud. 2. Follow the procedure listed in After working inside your system. 3. Verify if the memory module has been installed properly, by pressing F2 and navigating to System Setup Main Menu > System BIOS > Memory Settings . In the Memory Settings screen, the System Memory Size must reflect the updated capacity of the installed memory. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is firmly seated in the memory module socket. Run the system memory test in system diagnostics. Cooling fan Removing the internal cooling fan Prerequisites CAUTION: Never operate your system cover with the internal fan removed. The system can overheat and result in shutdown of the system and loss of data. CAUTION: Do not operate the system with the system cover removed for more than 5 minutes. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. Steps 1. Press the release tabs on the fan cable connector and disconnect it from the connector on the system board. 2. Holding the fan, press the release tab, and slide the fan out in the direction of the arrow marked on the fan. Installing and removing system components 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
NOTE:
The memory module socket has an alignment key that enables you to install the memory module in the socket
in only one orientation.
4.
Press the memory module with your thumbs until the ejectors firmly click into place.
Figure 53. Installing a memory module
Next steps
1.
Install the air shroud.
2.
Follow the procedure listed in
After working inside your system
.
3.
Verify if the memory module has been installed properly, by pressing F2 and navigating to System Setup Main Menu > System BIOS >
Memory Settings . In the Memory Settings screen, the System Memory Size must reflect the updated capacity of the installed
memory. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is
firmly seated in the memory module socket. Run the system memory test in system diagnostics.
Cooling fan
Removing the internal cooling fan
Prerequisites
CAUTION:
Never operate your system cover with the internal fan removed. The system can overheat and result in
shutdown of the system and loss of data.
CAUTION:
Do not operate the system with the system cover removed for more than 5 minutes.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud.
Steps
1.
Press the release tabs on the fan cable connector and disconnect it from the connector on the system board.
2.
Holding the fan, press the release tab, and slide the fan out in the direction of the arrow marked on the fan.
Installing and removing system components
75