Dell PowerEdge T440 EMC Installation and Service Manual - Page 131

Control panel assembly, Removing the control panel assembly

Get Dell PowerEdge T440 PDF manuals and user guides View all Dell PowerEdge T440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Control panel assembly Removing the control panel assembly Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. Steps 1. Using the Phillips #2 screwdriver, remove the screw that secures control panel to the chassis. 2. Disconnect the control panel cable and the control panel USB cable from the system board. CAUTION: Do not use excessive force when removing the control panel cables as it can damage the connectors. 3. Slide the control panel out of the chassis. NOTE: Follow the same steps to remove the control panel in the rack-mode configuration. Figure 89. Removing the control panel assembly 4. To remove the information tag, perform the following steps: a. Locate and press the tabs on the information tag. b. Push the information tag out of the slot to remove it from the control panel. NOTE: Retain the information tag to replace it in the new control panel. Installing the control panel assembly Prerequisites Follow the safety guidelines listed in Safety instructions. Installing and removing system components 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Control panel assembly
Removing the control panel assembly
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
Steps
1.
Using the Phillips #2 screwdriver, remove the screw that secures control panel to the chassis.
2.
Disconnect the control panel cable and the control panel USB cable from the system board.
CAUTION:
Do not use excessive force when removing the control panel cables as it can damage the connectors.
3.
Slide the control panel out of the chassis.
NOTE:
Follow the same steps to remove the control panel in the rack-mode configuration.
Figure 89. Removing the control panel assembly
4.
To remove the information tag, perform the following steps:
a.
Locate and press the tabs on the information tag.
b.
Push the information tag out of the slot to remove it from the control panel.
NOTE:
Retain the information tag to replace it in the new control panel.
Installing the control panel assembly
Prerequisites
Follow the safety guidelines listed in
Safety instructions
.
Installing and removing system components
131