Dell PowerEdge T440 EMC Installation and Service Manual - Page 96

Installing a hard drive backplane

Get Dell PowerEdge T440 PDF manuals and user guides View all Dell PowerEdge T440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Figure 51. Removing a backplane Next steps Install a hard drive backplane. Installing a hard drive backplane Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If installed, remove the front bezel. 4. Remove the air shroud. Steps 1. Use the hooks at the base of the system as guides to align the hard drive backplane. 2. Lower the hard-drive backplane into the system till the release pin locks in place, securing the hard drive backplane to the system. 3. Connect the data, signal, and power cables to the backplane. 96 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Figure 51. Removing a backplane
Next steps
Install a hard drive backplane
.
Installing a hard drive backplane
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If installed,
remove the front bezel
.
4.
Remove the air shroud
.
Steps
1.
Use the hooks at the base of the system as guides to align the hard drive backplane.
2.
Lower the hard-drive backplane into the system till the release pin locks in place, securing the hard drive backplane to the system.
3.
Connect the data, signal, and power cables to the backplane.
96
Installing and removing system components