Dell PowerEdge T440 EMC Installation and Service Manual - Page 74

Installing a drive blank

Get Dell PowerEdge T440 PDF manuals and user guides View all Dell PowerEdge T440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Figure 28. Removing a drive blank Next steps 1. Install a drive or a drive blank. Installing a drive blank The procedure for installing 2.5-inch and 3.5-inch drive blanks is identical. Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. If installed, remove the front bezel. CAUTION: Mixing drive blanks from previous generations of PowerEdge servers is not supported. Steps Insert the drive blank into the drive slot, and push the blank until the release button clicks into place. Figure 29. Installing a drive blank Next steps If removed, install the bezel. 74 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Figure 28. Removing a drive blank
Next steps
1.
Install a drive or a drive blank.
Installing a drive blank
The procedure for installing 2.5-inch and 3.5-inch drive blanks is identical.
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
If installed,
remove the front bezel
.
CAUTION:
Mixing drive blanks from previous generations of PowerEdge servers is not supported.
Steps
Insert the drive blank into the drive slot, and push the blank until the release button clicks into place.
Figure 29. Installing a drive blank
Next steps
If removed,
install the bezel
.
74
Installing and removing system components