Dell PowerEdge T440 EMC Installation and Service Manual - Page 86

Cabled drives, Removing the internal hard drive bay

Get Dell PowerEdge T440 PDF manuals and user guides View all Dell PowerEdge T440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Figure 41. Installing the optical drive cage or tape drive Next steps 1. Follow the procedure listed in After working inside your system. 2. If applicable, install the bezel. Cabled drives CAUTION: Do not turn off or restart your system while the drive is being formatted. Doing so can cause a drive failure. Removing the internal hard drive bay Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 61. 2. Follow the procedure listed in Before working inside your system on page 62. 3. Disconnect the data and power cable(s) from the hard drive(s). Steps 1. Loosen the two captive screws securing the internal hard drive bay to the chassis. 2. Lift the internal hard drive bay up and out of the chassis. 86 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Figure 41. Installing the optical drive cage or tape drive
Next steps
1.
Follow the procedure listed in
After working inside your system
.
2.
If applicable,
install the bezel
.
Cabled drives
CAUTION:
Do not turn off or restart your system while the drive is being formatted. Doing so can cause a drive failure.
Removing the internal hard drive bay
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 61.
2.
Follow the procedure listed in
Before working inside your system
on page 62.
3.
Disconnect the data and power cable(s) from the hard drive(s).
Steps
1.
Loosen the two captive screws securing the internal hard drive bay to the chassis.
2.
Lift the internal hard drive bay up and out of the chassis.
86
Installing and removing system components