Epson 7900p User Manual - Page 75

Communication Setup Options, a network when it's in standby mode; this setting also lets

Get Epson 7900p - PowerLite XGA LCD Projector PDF manuals and user guides
UPC - 010343852464
View all Epson 7900p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

■ Progressive (in the Advanced1 menu) This setting should normally be left at its default setting (Video or Film/Auto). Converts interlaced signals to progressive signals. When set to OFF, interlaced signals are processed without conversion (available for video signals only). ■ BNC Sync Termination (in the Advanced2 menu) This setting should normally be left Off (for TTL input). If an analog (75-ohm) terminator is required, as for a switcher, change the setting to ON. Communication Setup Options These options let you set up the projector so it can be monitored and controlled from a remote computer (see Chapter 5). ■ Standby Mode (in the Advanced1 menu) Select Network ON to enable the projector to be monitored over a network when it's in standby mode; this setting also lets you view images on an external monitor during standby, if the monitor has been connected to the projector's Monitor Out port. ■ Network (in the Advanced2 menu) Used for managing the projector over a network (see Chapter 5). If the network assigns addresses automatically, turn on DHCP. Otherwise, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address, if applicable. If you want to monitor the projector using a network management utility, select SNMP and enter at least one trap IP address. ■ COM Port (in the Advanced2 menu) Used for communicating with a computer running the EMP Link21L utility software. (You can download this utility free of charge from http://support.epson.com.) Select RS-232C or USB, depending on the port that's being used for communication with the computer. Turn off the projector and then turn it back on for the new setting to take effect. note Press the Num button on the remote control to use the number keypad. Zero Num button Fine-tuning the Projector 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Fine-tuning the Projector
75
■
Progressive (in the Advanced1 menu)
This setting should normally be left at its default setting (
Video
or
Film/Auto
). Converts interlaced signals to progressive signals.
When set to
OFF
, interlaced signals are processed without
conversion (available for video signals only).
■
BNC Sync Termination (in the Advanced2 menu)
This setting should normally be left
Off
(for TTL input). If an
analog (75-ohm) terminator is required, as for a switcher, change
the setting to
ON
.
Communication Setup Options
These options let you set up the projector so it can be monitored and
controlled from a remote computer (see Chapter 5).
■
Standby Mode (in the Advanced1 menu)
Select
Network ON
to enable the projector to be monitored over
a network when it’s in standby mode; this setting also lets you
view images on an external monitor during standby, if the
monitor has been connected to the projector’s
Monitor Out
port.
■
Network (in the Advanced2 menu)
Used for managing the projector over a network (see Chapter 5).
If the network assigns addresses automatically, turn on
DHCP
.
Otherwise, turn off
DHCP
and enter the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
, if applicable.
If you want to monitor the projector using a network
management utility, select
SNMP
and enter at least one trap IP
address.
■
COM Port (in the Advanced2 menu)
Used for communicating with a computer running the EMP
Link21L utility software. (You can download this utility free of
charge from http://support.epson.com.) Select
RS-232C
or
USB
,
depending on the port that’s being used for communication with
the computer. Turn off the projector and then turn it back on for
the new setting to take effect.
note
Press the
Num
button on
the remote control to use the
number keypad.
Num
button
Zero