HP ML115 HP ProLiant ML115 Generation 5 Server Maintenance and Service Guide - Page 44

mounting screws to the system board mounting holes and press down.

Get HP ML115 - ProLiant - G5 PDF manuals and user guides
UPC - 884962252765
View all HP ML115 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Figure 20 Installing the processor CAUTION: After you install the processor, you must reinstall the cooler on top of the processor socket. The thermal grease you applied on the contact surfaces of the cooler and the processor provides the necessary thermal bonding to allow the cooler to draw heat from the processor. CAUTION: To prevent processor overheating or system instability, use only a cooler assembly specified for the HP ProLiant ML115 G5 server. To replace cooler assembly: 1. See the label on the side of the cooler to find the cooler direction. Properly align the cooler mounting screws to the system board mounting holes and press down. 2. Twist the mounting screws clockwise to secure the cooler to the system board. 3. Connect the cooler cable to the connector on the system board. CAUTION: Failure to connect the cooler cable to the system board may result in damage to the processor and could cause the server to shut down without displaying messages. Removal and Replacement Procedures 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Removal and Replacement Procedures
44
Figure 20
Installing the processor
CAUTION:
After you install the processor, you must reinstall the cooler on top of the processor
socket. The thermal grease you applied on the contact surfaces of the cooler and the processor
provides the necessary thermal bonding to allow the cooler to draw heat from the processor.
CAUTION:
To prevent processor overheating or system instability, use only a cooler assembly
specified for the HP ProLiant ML115 G5 server.
To replace cooler assembly:
1.
See the label on the side of the cooler to find the cooler direction. Properly align the cooler
mounting screws to the system board mounting holes and press down.
2.
Twist the mounting screws clockwise to secure the cooler to the system board.
3.
Connect the cooler cable to the connector on the system board.
CAUTION:
Failure to connect the cooler cable to the system board may result in damage to the
processor and could cause the server to shut down without displaying messages.