HP ML115 HP ProLiant ML115 Generation 5 Server Maintenance and Service Guide - Page 82

Table 10, Error-Code, Error Message, Description / Corrective Action

Get HP ML115 - ProLiant - G5 PDF manuals and user guides
UPC - 884962252765
View all HP ML115 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Table 10 POST Error Messages Error-Code 012 048 04D 04E 04F 050 051 052 05E Error Message Description / Corrective Action CMOS Date/Time not Set The CMOS Date and/or Time are invalid. This error can be resolved by readjusting the system time in the Setup Utility. Password check failed Password is incorrect after retried a few times. Users might need to reset the password. Primary Master Hard Disk Error The IDE/ATAPI device configured as Primary Master could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Primary Slave Hard Disk Error The IDE/ATAPI device configured as Primary Slave could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Secondary Master Hard Disk The IDE/ATAPI device configured as Secondary Master could Error not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Secondary Slave Hard Disk Error The IDE/ATAPI device configured as Secondary Slave could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Master Hard Disk Error The IDE/ATAPI device configured as Master in the 3rd IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Master Slave Disk Error The IDE/ATAPI device configured as Slave in the 3rd IDE controller could not be properly initialized by the BIOS. This message is typically displayed When the BIOS is trying to detect and configure IDE/ATAPI devices in POST. Password check failed If user input incorrect password more than three times, then display this error information and continue to boot. Uncorrectable memory error System halts after displaying this message. If the problem persists, contact HP Customer Support. Microcode Error BIOS could not find or load the CPU Microcode Update to the CPU. The message is most likely to appear when a new CPU is installed in a system board with outdated BIOS. In this situation, you must update the BIOS to include the Microcode Update for the new CPU. Checking NVRAM Update BIOS could not write to the NVRAM block. This message Failed appears when the FLASH part is malfunctioning. Diagnostic tools and Setup Utilities 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Diagnostic tools and Setup Utilities
82
Table 10
POST Error Messages
Error-Code
Error Message
Description / Corrective Action
012
CMOS Date/Time not Set
The CMOS Date and/or Time are invalid. This error can be
resolved by readjusting the system time in the Setup Utility.
048
Password check failed
Password is incorrect after retried a few times. Users might
need to reset the password.
04D
Primary Master Hard Disk
Error
The IDE/ATAPI device configured as Primary Master could not
be properly initialized by the BIOS. This message is typically
displayed when the BIOS is trying to detect and configure
IDE/ATAPI devices in POST.
04E
Primary Slave Hard Disk
Error
The IDE/ATAPI device configured as Primary Slave could not
be properly initialized by the BIOS. This message is typically
displayed when the BIOS is trying to detect and configure
IDE/ATAPI devices in POST.
04F
Secondary Master Hard Disk
Error
The IDE/ATAPI device configured as Secondary Master could
not be properly initialized by the BIOS. This message is
typically displayed when the BIOS is trying to detect and
configure IDE/ATAPI devices in POST.
050
Secondary Slave Hard Disk
Error
The IDE/ATAPI device configured as Secondary Slave could
not be properly initialized by the BIOS. This message is
typically displayed when the BIOS is trying to detect and
configure IDE/ATAPI devices in POST.
051
Master Hard Disk Error
The IDE/ATAPI device configured as Master in the 3rd IDE
controller could not be properly initialized by the BIOS. This
message is typically displayed when the BIOS is trying to
detect and configure IDE/ATAPI devices in POST.
052
Master Slave Disk Error
The IDE/ATAPI device configured as Slave in the 3rd IDE
controller could not be properly initialized by the BIOS. This
message is typically displayed When the BIOS is trying to
detect and configure IDE/ATAPI devices in POST.
05E
Password check failed
If user input incorrect password more than three times, then
display this error information and continue to boot.
Uncorrectable memory error
System halts after displaying this message. If the problem
persists, contact HP Customer Support.
Microcode Error
BIOS could not find or load the CPU Microcode Update to the
CPU. The message is most likely to appear when a new CPU is
installed in a system board with outdated BIOS. In this
situation, you must update the BIOS to include the Microcode
Update for the new CPU.
Checking NVRAM Update
Failed
BIOS could not write to the NVRAM block. This message
appears when the FLASH part is malfunctioning.