HP ML115 HP ProLiant ML115 Generation 5 Server Maintenance and Service Guide - Page 46

Place the memory module on a static-dissipating work surface or inside of an anti-static

Get HP ML115 - ProLiant - G5 PDF manuals and user guides
UPC - 884962252765
View all HP ML115 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

CAUTION: DIMMs can be damaged by improper handing. Always use an anti-static wrist strap and grounding mat, and discharge static electricity before touching DIMMs. To remove a memory module: NOTE: Lay the server on its side with the open side facing up. If necessary, remove any accessory boards or cables that prevent access to the memory socket. 1. Completely open the holding clips securing the module. 2. Gently pull the memory module upward to remove it from the socket. Figure 23 Removing a memory module CAUTION: Place the memory module on a static-dissipating work surface or inside of an anti-static bag. To install a memory module: 1. Align the notch on the bottom edge of the module with the keyed surface of the DIMM slot and then press the module fully into the slot. 2. Firmly press the holding clips inward to secure the memory module in place. Removal and Replacement Procedures 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Removal and Replacement Procedures
46
CAUTION:
DIMMs can be damaged by improper handing. Always use an anti-static wrist strap and
grounding mat, and discharge static electricity before touching DIMMs.
To remove a memory module:
NOTE:
Lay the server on its side with the open side facing up. If necessary, remove any accessory
boards or cables that prevent access to the memory socket.
1.
Completely open the holding clips securing the module.
2.
Gently pull the memory module upward to remove it from the socket.
Figure 23
Removing a memory module
CAUTION:
Place the memory module on a static-dissipating work surface or inside of an anti-static
bag.
To install a memory module:
1.
Align the notch on the bottom edge of the module with the keyed surface of the DIMM slot and
then press the module fully into the slot.
2.
Firmly press the holding clips inward to secure the memory module in place.