HP StorageWorks MSA1510i HP StorageWorks 1510i Modular Smart Array installatio - Page 102

Changing the management port IP address through the MSA1510i controller display panel, Verify

Get HP StorageWorks MSA1510i PDF manuals and user guides View all HP StorageWorks MSA1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

1. Power Off the MSA storage system as detailed in Powering off the MSA1510i. 2. Move the hard drives. 3. Power on the MSA storage system as detailed in Powering on the MSA. 4. The following message should be displayed on the LCD front panel of the controller 86 DRIVE POSITION CHANGE DETECTED. IMPORTANT: If the following LCD message is displayed: 121 NO VOLUMES DETECTED, turn off the system immediately to avoid data loss, and return the hard drives to their original locations. 5. Check the new configuration by running the ACU, SMU, or MSA-CLI. Changing the management port IP address through the MSA1510i controller display panel When the MSA1510i is initially installed and powered on, an IP address is automatically assigned to the primary management port (usually MA0). Depending on your network configuration, this default IP address may not be accessible by the network servers. To change the IP address of the MSA1510i management port to be in the same LAN segment as the network servers, do the following: 1. Access the controller LCD panel management menu. Press the right (>) navigation button on the front of the active controller (usually the front-right controller.) Network Settings should be displayed and blinking. LCD panel navigation buttons work as follows: Navigation button In the menu Within a menu option Right (>) Select a blinking menu option. When changing IP address settings, move to the next digit. Up/Down (^/v) Scroll through the menu options. Change/Toggle a setting. Left ( to select it. b. Press ^ or v until DHCP Enabled is displayed and blinking, and then press > to select it. c. Press ^ or v to change the setting to No. d. Press < to accept the new setting and return to the initial management menu display. 3. Change the IP address. a. With Network Settings displayed and blinking, press > to select it. b. Press ^ or v until IP Address is displayed and blinking, and then press > to select it. c. Press ^ or v to scroll through and select the value for each digit of the IP address. d. After entering all digits of the new IP address, press < to accept the new setting and return to the initial management menu display. 4. Verify and, if necessary, change the Subnet Mask, Default Gateway, Primary DNS, Secondary DNS, and VLAN ID using procedures similar to those outlined in step 3, but pressing ^ or v to navigate to the desired menu option. 102 Operation and management

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
1.
Power Off the MSA storage system as detailed in
Powering off the MSA1510i
.
2.
Move the hard drives.
3.
Power on the MSA storage system as detailed in
Powering on the MSA
.
4.
The following message should be displayed on the LCD front panel of the controller
86 DRIVE
POSITION CHANGE DETECTED
.
IMPORTANT:
If the following LCD message is displayed:
121 NO VOLUMES DETECTED
, turn off the
system immediately to avoid data loss, and return the hard drives to their original locations.
5.
Check the new con
fi
guration by running the ACU, SMU, or MSA-CLI.
Changing the management port IP address through the
MSA1510i controller display panel
When the MSA1510i is initially installed and powered on, an IP address is automatically assigned to
the primary management port (usually MA0). Depending on your network con
fi
guration, this default IP
address may not be accessible by the network servers.
To change the IP address of the MSA1510i management port to be in the same LAN segment as the
network servers, do the following:
1.
Access the controller LCD panel management menu. Press the right (>) navigation button on the
front of the active controller (usually the front-right controller.) Network Settings should be displayed
and blinking.
LCD panel navigation buttons work as follows:
Navigation button
In the menu
Within a menu option
Right (>)
Select a blinking menu option.
When changing IP address
settings, move to the next digit.
Up/Down (^/v)
Scroll through the menu options.
Change/Toggle a setting.
Left (<)
Not applicable.
Accept the displayed setting and
return to the initial management
menu display.
2.
Disable DHCP.
a.
With
Network Settings
displayed and blinking, press
>
to select it.
b.
Press
^
or
v
until
DHCP Enabled
is displayed and blinking, and then press
>
to select it.
c.
Press
^
or
v
to change the setting to No.
d.
Press
<
to accept the new setting and return to the initial management menu display.
3.
Change the IP address.
a.
With
Network Settings
displayed and blinking, press
>
to select it.
b.
Press
^
or
v
until
IP Address
is displayed and blinking, and then press
>
to select it.
c.
Press
^
or
v
to scroll through and select the value for each digit of the IP address.
d.
After entering all digits of the new IP address, press
<
to accept the new setting and return to the
initial management menu display.
4.
Verify and, if necessary, change the Subnet Mask, Default Gateway, Primary DNS, Secondary DNS,
and VLAN ID using procedures similar to those outlined in step 3, but pressing ^ or v to navigate
to the desired menu option.
102
Operation and management