HP StorageWorks MSA1510i HP StorageWorks 1510i Modular Smart Array installatio - Page 121

Autoflash Started, Temperature Ok

Get HP StorageWorks MSA1510i PDF manuals and user guides View all HP StorageWorks MSA1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Message 150 BEACON ON 151 BEACON OFF 201 ARRAY CONTROLLER TEMPERATURE OK 202 ARRAY CONTROLLER OVERHEATING 203 ARRAY CONTROLLER OVERHEATED 204 ARRAY CONTROLLER DISABLED Type Informational Informational Informational Error Error Error Description Action The LEDs on the MSA and all connected hard drives are blinking because that array controller was selected for identification or configuration in a host-based application such as the ACU or SMU. The LEDs on the MSA and all connected hard drives are no longer blinking because the host-based application is no longer identifying or configuring this MSA. The temperature sensor on the array controller indicates that the temperature that was previously exceeding the normal operating range is now back within the range. The temperature sensor on the array controller indicates that the array controller is starting to exceed the normal operating range. Check all MSA fans and ensure they are operating. Any failed fan should be replaced. Ensure that there is a module or blanking panel (cover plate) in all MSA chassis bays and slots. Empty bays affect the airflow and cooling ability of the MSA. The temperature sensor on the array controller indicates that the array controller has exceeded the safe operating range. The MSA should be powered off as soon as possible to avoid hardware failure. Check all MSA fans and ensure they are operating. Any failed fan should be replaced. Ensure that there is a module or blanking panel (cover plate) in all MSA chassis bays and slots. Empty bays affect the airflow and cooling ability of the MSA. The array controller has been disabled due to a redundancy failure. Remove the disabled array controller, wait 10 seconds, and then reinsert the array controller, ensuring that it is fully seated in the chassis. If the issue persists, contact HP support. 205 ARRAY CONTROLLER RESTARTING Informational 300 RECOVERY ROM AUTOFLASH STARTED Informational The array controller has completed firmware cloning and is being restarted automatically. The array controller has detected that the firmware's backup recovery ROM image is invalid and is copying the current active firmware image into the backup recovery ROM. 1510i Modular Smart Array installation and user guide 121

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Message
Type
Description
Action
150 BEACON ON
Informational
The LEDs on the MSA and all
connected hard drives are blinking
because that array controller
was selected for identi
fi
cation
or con
fi
guration in a host-based
application such as the ACU or
SMU.
151 BEACON OFF
Informational
The LEDs on the MSA and all
connected hard drives are no
longer blinking because the
host-based application is no longer
identifying or con
fi
guring this
MSA.
201 ARRAY
CONTROLLER
TEMPERATURE OK
Informational
The temperature sensor on the
array controller indicates that the
temperature that was previously
exceeding the normal operating
range is now back within the
range.
202 ARRAY
CONTROLLER
OVERHEATING
Error
The temperature sensor on the
array controller indicates that
the array controller is starting
to exceed the normal operating
range.
Check all MSA fans and ensure
they are operating. Any failed
fan should be replaced. Ensure
that there is a module or blanking
panel (cover plate) in all MSA
chassis bays and slots. Empty
bays affect the air
fl
ow and cooling
ability of the MSA.
203 ARRAY
CONTROLLER
OVERHEATED
Error
The temperature sensor on the
array controller indicates that the
array controller has exceeded the
safe operating range.
The MSA should be powered
off as soon as possible to avoid
hardware failure.
Check all MSA fans and ensure
they are operating. Any failed
fan should be replaced. Ensure
that there is a module or blanking
panel (cover plate) in all MSA
chassis bays and slots. Empty
bays affect the air
fl
ow and cooling
ability of the MSA.
204 ARRAY
CONTROLLER
DISABLED
Error
The array controller has been
disabled due to a redundancy
failure.
Remove the disabled array
controller, wait 10 seconds, and
then reinsert the array controller,
ensuring that it is fully seated in
the chassis.
If the issue persists, contact HP
support.
205 ARRAY
CONTROLLER
RESTARTING
Informational
The array controller has completed
fi
rmware cloning and is being
restarted automatically.
300 RECOVERY ROM
AUTOFLASH STARTED
Informational
The array controller has detected
that the
fi
rmware's backup
recovery ROM image is invalid
and is copying the current active
fi
rmware image into the backup
recovery ROM.
1510i Modular Smart Array installation and user guide
121