HP Tc4100 hp server tc4100 operation and maintenance guide (English, 2.1) - Page 118

Installing the Diagnostic Board, Power down the HP Server. Refer

Get HP Tc4100 - Server - 256 MB RAM PDF manuals and user guides View all HP Tc4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Chapter 7 Replacing Parts Removing the Diagnostic Board 1. Power down the HP Server. Refer to "Powering Down the HP Server tc4100" on page 14. 2. Disconnect the power cord(s). WARNING The power supplies continue to provide standby voltage to the HP Server until the power cord(s) is/are disconnected. 3. If rack-mounted, extend the HP Server out of the rack. 4. Remove left cover (pedestal) or top cover (rack-mounted) from the HP Server. Refer to "Opening and Closing the HP Server tc4100" on page 21. NOTE Wear a wrist strap and use a static-dissipating work surface connected to the chassis when handling components. Ensure that the metal of the wrist strap contacts your skin. Visual Diagnostic Tab Board (4 Places) 2 1 Tab slot (4 Places) Figure 7-14. Diagnostic Board Removal 5. Remove the signal connectors from the diagnostic board. 6. Push the diagnostic board cover to the right; lift the board from the chassis. 7. Separate the diagnostic board from the cover. The cover will be used with the replacement diagnostic board. Installing the Diagnostic Board 1. Install the replacement diagnostic board in the cover saved earlier. 116

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
116
Chapter 7
Replacing Parts
Removing the Diagnostic Board
1.
Power down the HP Server. Refer to
“Powering Down the HP Server tc4100” on page 14
.
2.
Disconnect the power cord(s).
3.
If rack-mounted, extend the HP Server out of the rack.
4.
Remove left cover (pedestal) or top cover (rack-mounted) from the HP Server. Refer to
“Opening and
Closing the HP Server tc4100” on page 21
.
Figure 7-14.
Diagnostic Board Removal
5.
Remove the signal connectors from the diagnostic board.
6.
Push the diagnostic board cover to the right; lift the board from the chassis.
7.
Separate the diagnostic board from the cover. The cover will be used with the replacement diagnostic board.
Installing the Diagnostic Board
1.
Install the replacement diagnostic board in the cover saved earlier.
WARNING
The power supplies continue to provide standby voltage to the HP Server until the power
cord(s) is/are disconnected.
NOTE
Wear a wrist strap and use a static-dissipating work surface connected to the chassis
when handling components. Ensure that the metal of the wrist strap contacts your skin.
Visual
Diagnostic
Board
Tab
(4 Places)
Tab slot
(4 Places)
1
2