HP Tc4100 hp server tc4100 operation and maintenance guide (English, 2.1) - Page 76

Hard Disk Controller, Video Memory boot

Get HP Tc4100 - Server - 256 MB RAM PDF manuals and user guides View all HP Tc4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Chapter 4 Error Messages Table 4-1. POST Error Codes Code 0540 0600 0700 0712 0713 Description Problem/Solution Hard Disk Controller POST has detected an address space or IRQ resource conflict between resource conflict the integrated hard disk controller and an accessory board. To correct this: 1. If the integrated hard disk controller is not needed, run the Setup Utility to disable it (primary or secondary). 2. If the integrated hard disk controller is needed, the accessory board's IRQ and address space must be reconfigured to use other free resources. Refer to the accessory board installation manual for information. Video Memory boot The video memory size detected during POST is smaller than error previously detected. (This does not apply to To correct this: tc4100) 1. If you have changed your video adapter, press F4 to automatically validate the change. 2. If the problem persists, the system board may need to be replaced. Contact your service representative. DIMM size boot error The system memory size detected during the POST is smaller than previously detected. One or several DIMMs are either disconnected, or have been replaced by smaller ones. To correct this: 1. If some main DIMMs have just been removed or replaced by smaller ones, press F4 to automatically validate the change. 2. If no DIMM has been removed or changed, ensure all DIMMs are properly inserted in the slots. 3. If the problem persists, one of DIMMs may need to be replaced. Contact your service representative. DIMM installation error POST has detected an incorrectly installed DIMM or the failure of one or more DIMMs. To correct this: 1. If additional memory was just installed in your server, please verify the installation conforms to the description in the User's Guide. 2. If this error was reported when no additional memory was just installed, restart the server. 3. If the error persists, contact your service representative. Incorrect DIMM installed POST has detected one or more DIMMs are not the correct type, or the correct speed. To correct this: 1. If additional memory was just installed in your server, please verify the correct DIMM type and speed for this server was installed. Refer to the DIMM description in "Memory Modules" in Chapter 3, "Installing TC4100." 2. If this error was reported when no additional memory was just installed, restart the server. 3. If the error persists, contact your service representative. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
74
Chapter 4
Error Messages
0540
Hard Disk Controller
resource conflict
POST has detected an address space or IRQ resource conflict between
the integrated hard disk controller and an accessory board.
To correct this:
1.
If the integrated hard disk controller is not needed, run the Setup
Utility to disable it (primary or secondary).
2.
If the integrated hard disk controller is needed, the accessory
board's IRQ and address space must be reconfigured to use other
free resources. Refer to the accessory board installation manual
for information.
0600
Video Memory boot
error
(This does not apply to
tc4100)
The video memory size detected during POST is smaller than
previously detected.
To correct this:
1.
If you have changed your video adapter, press F4 to automatically
validate the change.
2.
If the problem persists, the system board may need to be replaced.
Contact your service representative.
0700
DIMM size boot error
The system memory size detected during the POST is smaller than
previously detected. One or several DIMMs are either disconnected,
or have been replaced by smaller ones.
To correct this:
1.
If some main DIMMs have just been removed or replaced by
smaller ones, press F4 to automatically validate the change.
2.
If no DIMM has been removed or changed, ensure all DIMMs are
properly inserted in the slots.
3.
If the problem persists, one of DIMMs may need to be replaced.
Contact your service representative.
0712
DIMM installation
error
POST has detected an incorrectly installed DIMM or the failure of
one or more DIMMs.
To correct this:
1.
If additional memory was just installed in your server, please ver-
ify the installation conforms to the description in the User's Guide.
2.
If this error was reported when no additional memory was just
installed, restart the server.
3.
If the error persists, contact your service representative.
0713
Incorrect DIMM
installed
POST has detected one or more DIMMs are not the correct type, or
the correct speed.
To correct this:
1.
If additional memory was just installed in your server, please ver-
ify the correct DIMM type and speed for this server was installed.
Refer to the DIMM description in “Memory Modules” in Chapter
3, “Installing TC4100.”
2.
If this error was reported when no additional memory was just
installed, restart the server.
3.
If the error persists, contact your service representative.
Table 4-1.
POST Error Codes
Code
Description
Problem/Solution