HP Tc4100 hp server tc4100 operation and maintenance guide (English, 2.1) - Page 35

PCI SCSI Card or a PCI HP NetRAID, Flat Twisted Pair SCSI Cable

Get HP Tc4100 - Server - 256 MB RAM PDF manuals and user guides View all HP Tc4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Chapter 3 Installing and Configuring • The Hot Swap Mass Storage Cage can also be split into two parts, with up to two drives on one SCSI bus and 6 drives on the other SCSI bus (requires duplex board accessory kit). This requires two SCSI cables (additional SCSI cables are included in the duplex board accessory kit). If the duplex board is installed, the embedded dual channel SCSI controller, a dual channel SCSI disk controller board, or a DAC board must be used to control the two halves of the Hot Swap Mass Storage Cage. Table 3-1. Internal Cable Designations Cable Designation Floppy Disk Cable IDE Cable Round Twisted Pair SCSI Cable Flat Twisted Pair SCSI Cable Internal/External SCSI Cable Description Source This cable always connects to This cable can only connect to the the Flexible disk drive in the floppy connector on the system board. system. This cable always connects to This cable can only connect to the the IDE devices (CD-ROM) in embedded IDE connector on the the HP Server tc4100. system board. This cable always connects to the non-hot swap drives and has a termination at the end. This cable can be connected only to the embedded SCSI A channel and a PCI SCSI Card or a PCI HP NetRAID card. This cable always connects to the Hot Swap Mass Storage Cage and has no termination. This cable is typically connected to the embedded SCSI B channel, a SCSI disk controller board, or a HP NetRAID (DAC) board. This sheathed ribbon cable (optional) is always used for the external connector. This cable can be connected only to the embedded SCSI channel A. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
33
Chapter 3
Installing and Configuring
•
The Hot Swap Mass Storage Cage can also be split into two parts, with up to two drives on one SCSI bus
and 6 drives on the other SCSI bus (requires duplex board accessory kit). This requires two SCSI cables
(additional SCSI cables are included in the duplex board accessory kit).
If the duplex board is installed, the embedded dual channel SCSI controller, a dual channel SCSI disk
controller board, or a DAC board must be used to control the two halves of the Hot Swap Mass Storage
Cage.
Table 3-1.
Internal Cable Designations
Cable Designation
Description
Source
Floppy Disk Cable
This cable always connects to
the Flexible disk drive in the
system.
This cable can only connect to the
floppy connector on the system board.
IDE Cable
This cable always connects to
the IDE devices (CD-ROM) in
the HP Server tc4100.
This cable can only connect to the
embedded IDE connector on the
system board.
Round Twisted Pair SCSI Cable
This cable always connects to
the non-hot swap drives and
has a termination at the end.
This cable can be connected only to
the embedded SCSI A channel and a
PCI SCSI Card or a PCI HP NetRAID
card.
Flat Twisted Pair SCSI Cable
This cable always connects to
the Hot Swap Mass Storage
Cage and has no termination.
This cable is typically connected to the
embedded SCSI B channel, a SCSI
disk controller board, or a HP
NetRAID (DAC) board.
Internal/External SCSI Cable
This sheathed ribbon cable
(optional) is always used for
the external connector.
This cable can be connected only to
the embedded SCSI channel A.