HP Tc4100 hp server tc4100 operation and maintenance guide (English, 2.1) - Page 72

Error Messages, Power-On Self Test (POST) Error Codes

Get HP Tc4100 - Server - 256 MB RAM PDF manuals and user guides View all HP Tc4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

4 Error Messages Power-On Self Test (POST) Error Codes Error messages (POST Codes) are encountered if an error condition occurs during the boot process of the HP Server tc4100. All codes and their respective descriptions are listed in the following table; all the codes may not apply to your server. These codes will appear on the display monitor, provided it and the supporting circuitry are functioning. NOTE Do not take remove/replacement actions until you have taken other troubleshooting steps. See "Preventive Maintenance" on page 83. Table 4-1. POST Error Codes Code 0000 Description System Board error 0010 BIOS problem 0011 Battery problem 0012 0050 BIOS initialization problem Processor Cooling/ Heating problem Problem/Solution POST has detected a failure limited to the system board internal functions. To verify this error: 1. Reboot the server. Skipping this error message and continuing may result in unstable behavior, or a system hang during the boot process. 2. If this error continues, the system board may need to be replaced. Contact your service representative. The PC configuration has been lost, cleared, corrupted, or has not been initialized. When the HP Server remains unplugged for a long period of time, the battery will discharge and not provide enough current to keep the CMOS memory powered. To correct this: 1. Verify the battery is properly inserted. 2. 2. If necessary, replace the battery as described in your user's guide. Run the Setup Utility to re-configure your server. The server BIOS is not responding due to a possible battery discharge. If the HP Server was unplugged for a long period of time, the battery will discharge and not provide enough current to keep the system date and time current. To correct this: 1. Verify the battery is properly inserted. 2. If necessary, replace the battery. 3. Set time and date using the Setup utility or from your operating system. The HP Server configuration has been cleared or has not been initialized. Run the Setup Utility to re-configure your system. POST has detected a cooling fan problem. 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
70
Power-On Self Test (POST) Error Codes
Error messages (POST Codes) are encountered if an error condition occurs during the boot process of the HP
Server tc4100. All codes and their respective descriptions are listed in the following table; all the codes may
not apply to your server.
These codes will appear on the display monitor, provided it and the supporting circuitry are functioning.
4
Error Messages
NOTE
Do not take remove/replacement actions until you have taken other troubleshooting
steps. See
“Preventive Maintenance” on page 83
.
Table 4-1.
POST Error Codes
Code
Description
Problem/Solution
0000
System Board error
POST has detected a failure limited to the system board internal
functions.
To verify this error:
1.
Reboot the server.
Skipping this error message and continuing may result in unstable
behavior, or a system hang during the boot process.
2.
If this error continues, the system board may need to be replaced.
Contact your service representative.
0010
BIOS problem
The PC configuration has been lost, cleared, corrupted, or has not
been initialized. When the HP Server remains unplugged for a long
period of time, the battery will discharge and not provide enough
current to keep the CMOS memory powered.
To correct this:
1.
Verify the battery is properly inserted.
2.
2. If necessary, replace the battery as described in your user's
guide.
Run the Setup Utility to re-configure your server.
0011
Battery problem
The server BIOS is not responding due to a possible battery discharge.
If the HP Server was unplugged for a long period of time, the battery
will discharge and not provide enough current to keep the system date
and time current.
To correct this:
1.
Verify the battery is properly inserted.
2.
If necessary, replace the battery.
3.
Set time and date using the Setup utility or from your operating
system.
0012
BIOS initialization
problem
The HP Server configuration has been cleared or has not been
initialized.
Run the Setup Utility to re-configure your system.
0050
Processor Cooling/
Heating problem
POST has detected a cooling fan problem.