HP Vectra VE C/xxx 7 HP Vectra VE C/xxx Series 7 PC - Upgrade and Maintenance - Page 94

Setting the Device Boot Order

Get HP Vectra VE C/xxx 7 PDF manuals and user guides View all HP Vectra VE C/xxx 7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

NOTE 4 Troubleshooting Your PC Setting the Device Boot Order Setting the Device Boot Order To select the drive to start (boot) from, you must enter the Setup program and go to Advanced - Advanced CMOS Setup. You can then select the 1st, 2nd, 3rd, and 4th Boot Devices. Connecting a hard disk drive to the IDE master connector does not ensure that the PC will boot on that hard disk drive. The first time you start your PC, the PC will by default boot from the hard disk drive connected to the Master IDE connector on the Primary IDE cable (IDE-0). The drive positions on the two IDE cables are: Cable Primary IDE Primary IDE Secondary IDE Secondary IDE Connector Master Slave Master Slave BIOS ID (in Setup Program) IDE-0 IDE-1 IDE-2 IDE-3 When booting from a different hard disk drive, make sure you know its physical position on the cable. 84 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
4
Troubleshooting Your PC
Setting the Device Boot Order
84
English
Setting the Device Boot Order
To select the drive to start (boot) from, you must enter the
Setup
program and go to
Advanced - Advanced CMOS Setup
. You can then
select the 1st, 2nd, 3rd, and 4th Boot Devices. Connecting a hard disk
drive to the IDE master connector
does not
ensure that the PC will
boot on that hard disk drive.
NOTE
The first time you start your PC, the PC will by default boot from the
hard disk drive connected to the Master IDE connector on the Primary
IDE cable (IDE-0).
The drive positions on the two IDE cables are:
When booting from a different hard disk drive, make sure you know its
physical position on the cable.
Cable
Connector
BIOS ID (in
Setup
Program)
Primary IDE
Master
IDE-0
Primary IDE
Slave
IDE-1
Secondary IDE
Master
IDE-2
Secondary IDE
Slave
IDE-3