HP Xw8200 HP Workstation xw8200 Service and Technical Reference Guide (Complet - Page 75

System Fan

Get HP Xw8200 - Workstation - 1 GB RAM PDF manuals and user guides
UPC - 882780210455
View all HP Xw8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Chapter 4 3 Disconnect the optical drives, diskette drive, hard drives, and graphics card (select models only) from the power supply. CAUTION Be sure you can differentiate which power cable was disconnected from the PCI Express x16 graphics card and which power cable was disconnected from the system board. These two cables look very similar. The PCI Express power cable has a black connector and the power cable has a white connector. When power is present, you must NEVER connect the PCI Express power cable to the system board. If you do so, the system board may be damaged and your warranty voided. To see a picture of the PCI Express cable and where it must be connected, refer to the "PCI or PCI Express Installation" section on page 84. 4 Remove the four screws 1 from the back panel. 5 Slide the power supply toward the front and lift up 2 to remove it from the chassis. 1 2 To install the power supply, reverse the previous steps. System Fan To remove the system fan: 1 Disconnect power from the system (page 66), remove the access panel (page 71), and lay the workstation on its side with the system board facing up. 2 Disconnect the fan plug 1 from the system board. REMOVAL AND REPLACEMENT OF COMPONENTS 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
REMOVAL AND REPLACEMENT OF COMPONENTS
75
Chapter 4
3
Disconnect the optical drives, diskette drive, hard drives, and graphics card (select models only) from
the power supply.
CAUTION
Be sure you can differentiate which power cable was disconnected from the PCI Express x16
graphics card and which power cable was disconnected from the system board. These two cables look
very similar. The PCI Express power cable has a black connector and the power cable has a white
connector. When power is present, you must NEVER connect the PCI Express power cable to the
system board. If you do so, the system board may be damaged and your warranty voided. To see a
picture of the PCI Express cable and where it must be connected, refer to the
“PCI or PCI Express
Installation” section on page 84
.
4
Remove the four screws
1
from the back panel.
5
Slide the power supply toward the front and lift up
2
to remove it from the chassis.
To install the power supply, reverse the previous steps.
System Fan
To remove the system fan:
1
Disconnect power from the system (
page 66
), remove the access panel (
page 71
), and lay the
workstation on its side with the system board facing up.
2
Disconnect the fan plug
1
from the system board.
1
2