HP Xw8200 HP Workstation xw8200 Service and Technical Reference Guide (Complet - Page 95

more than two, If installing more than two SATA hard drives, you must install a SATA controller card.

Get HP Xw8200 - Workstation - 1 GB RAM PDF manuals and user guides
UPC - 882780210455
View all HP Xw8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Chapter 4 SATA For more information on SATA hard drives and the SATA RAID configuration, see Appendix B, "SATA Devices," on page 145. To install one or two SATA drives: 1 Select a drive bay in which to install the drive. Squeeze the green tabs and slide the rails out of the empty bay. 2 Attach the rails to the hard drive by aligning the notches with the holes and squeezing it into place (see image on page 93). 3 Push the drive into the selected bay until it snaps into place. 4 Attach the power cable and data cable to the drive. 5 Connect the data cable to the serial ATA port. To install more than two SATA hard drives: NOTE If installing more than two SATA hard drives, you must install a SATA controller card. 1 Select a drive bay in which to install the drive. 2 Squeeze the green tabs and slide the rails out of the empty bay (see image on page 92). 3 Attach the rails to the hard drive by aligning the notches with the holes and squeezing it into place (see image on page 93). 4 Push the drive into the selected bay until it snaps into place. 5 Attach the power and data cable to the drive. 6 Insert the SATA controller card into an available PCI expansion slot (page 84). 7 Connect the other end of the SATA cable to the SATA controller card. REMOVAL AND REPLACEMENT OF COMPONENTS 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
REMOVAL AND REPLACEMENT OF COMPONENTS
95
Chapter 4
SATA
For more information on SATA hard drives and the SATA RAID configuration, see Appendix B, “SATA
Devices,” on
page 145
.
To install
one
or
two
SATA drives:
1
Select a drive bay in which to install the drive. Squeeze the green tabs and slide the rails out of the
empty bay.
2
Attach the rails to the hard drive by aligning the notches with the holes and squeezing it into place
(see image on
page 93
).
3
Push the drive into the selected bay until it snaps into place.
4
Attach the power cable and data cable to the drive.
5
Connect the data cable to the serial ATA port.
To install
more than two
SATA hard drives:
NOTE
If installing more than two SATA hard drives, you must install a SATA controller card.
1
Select a drive bay in which to install the drive.
2
Squeeze the green tabs and slide the rails out of the empty bay (see image on
page 92
).
3
Attach the rails to the hard drive by aligning the notches with the holes and squeezing it into place
(see image on
page 93
).
4
Push the drive into the selected bay until it snaps into place.
5
Attach the power and data cable to the drive.
6
Insert the SATA controller card into an available PCI expansion slot (
page 84
).
7
Connect the other end of the SATA cable to the SATA controller card.