HP Xw8200 HP Workstation xw8200 Service and Technical Reference Guide (Complet - Page 89

Replacing Optical Drive Cable, Diskette Drive (Optional)

Get HP Xw8200 - Workstation - 1 GB RAM PDF manuals and user guides
UPC - 882780210455
View all HP Xw8200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Chapter 4 If you are installing more than one optical drive, route the cable as in the following image. NOTE The optical drive cable is routed under the system board. Replacing Optical Drive Cable The optical IDE cable is routed behind the system board. 1 Disconnect power from the system (page 66), remove the access panel (page 71), lay the workstation on its side with the system board facing up, remove all expansion boards and graphics cards (page 84), remove the CPU heatsinks (page 96), disconnect the optical IDE cable from the system board, and remove the system board (page 101). 2 Remove the plastic ties and tape from the IDE cable, then remove the IDE cable 3 Replace the cable and cable ties. Refer to the previous image for cable routing information. Diskette Drive (Optional) To remove a diskette drive: 1 Disconnect power from the system (page 66), remove the access panel (page 71), and remove the front bezel (page 71). REMOVAL AND REPLACEMENT OF COMPONENTS 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
REMOVAL AND REPLACEMENT OF COMPONENTS
89
Chapter 4
If you are installing more than one optical drive, route the cable as in the following image.
NOTE
The optical drive cable is routed under the system board.
Replacing Optical Drive Cable
The optical IDE cable is routed behind the system board.
1
Disconnect power from the system (
page 66
), remove the access panel (
page 71
), lay the
workstation on its side with the system board facing up, remove all expansion boards and graphics
cards (
page 84
), remove the CPU heatsinks (
page 96
), disconnect the optical IDE cable from the
system board, and remove the system board (
page 101
).
2
Remove the plastic ties and tape from the IDE cable, then remove the IDE cable
3
Replace the cable and cable ties. Refer to the previous image for cable routing information.
Diskette Drive (Optional)
To remove a diskette drive:
1
Disconnect power from the system (
page 66
), remove the access panel (
page 71
), and remove the
front bezel (
page 71
).