HP d248 HP Compaq Business Desktop d200 Series Personal Computers Service Refe - Page 43

Front Bezel, Preparation for Disassembly, Access Panel

Get HP d248 - Microtower Desktop PC PDF manuals and user guides View all HP d248 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Removal and Replacement Procedures- Microtower Type 2 Chassis 6.3 Front Bezel 1. Prepare the computer for disassembly (Section 6.1, "Preparation for Disassembly"). 2. Remove the access panels (Section 6.2, "Access Panel"). 3. Grasp the bottom of the front panel below the lowest air vent and pull the panel out and up to release it from the chassis. To install the front bezel, insert the top two latches into their respective holes in the chassis and push the bezel in until it is fully seated. ✎ The front bezel shown may be different than the one on your computer but the removal and replacement procedures are identical. ✎ When replacing the front bezel, ensure that the top of the front bezel is flush with the top of the chassis before pressing it into place. ✎ Some models may not have an air shroud surrounding the processor. Service Reference Guide, d200 336493-004 6-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Service Reference Guide, d200
336493-004
6–3
Removal and Replacement Procedures— Microtower Type 2 Chassis
6.3 Front Bezel
1. Prepare the computer for disassembly (
Section 6.1, “Preparation for Disassembly”
).
2. Remove the access panels (
Section 6.2, “Access Panel”
).
3.
Grasp the bottom of the front panel below the lowest air vent and pull the panel out and up to
release it from the chassis.
To install the front bezel, insert the top two latches into their respective holes in the chassis and
push the bezel in until it is fully seated.
✎
The front bezel shown may be different than the one on your computer but the removal and
replacement procedures are identical.
✎
When replacing the front bezel, ensure that the top of the front bezel is flush with the top of the
chassis before pressing it into place.
✎
Some models may not have an air shroud surrounding the processor.