HP d248 HP Compaq Business Desktop d200 Series Personal Computers Service Refe - Page 57

Speaker

Get HP d248 - Microtower Desktop PC PDF manuals and user guides View all HP d248 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Removal and Replacement Procedures- Microtower Type 2 Chassis 6.10 Speaker 1. Prepare the computer for disassembly (Section 6.1, "Preparation for Disassembly"). 2. Remove the right access panel (Section 6.2, "Access Panel"). 3. Remove the front bezel (Section 6.3, "Front Bezel"). 4. Disconnect the speaker cable from the system board 1. 5. From the outside of the chassis pull out the stems of the four push pins to release the speakers then, remove the speaker 2. When installing the speakers, hold the plastic pin retainers firmly in place as they tend to be pushed out of the chassis holes when the speaker is being positioned. Once a speaker mounting hole has been properly aligned and the pin retainer pressed into it, insert the push pin to secure the pin retainer. To ensure proper alignment, install the push pins in an X pattern. Service Reference Guide, d200 336493-004 6-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Service Reference Guide, d200
336493-004
6–17
Removal and Replacement Procedures— Microtower Type 2 Chassis
6.10 Speaker
1. Prepare the computer for disassembly (
Section 6.1, “Preparation for Disassembly”
).
2. Remove the right access panel (
Section 6.2, “Access Panel”
).
3. Remove the front bezel (
Section 6.3, “Front Bezel”
).
4. Disconnect the speaker cable from the system board
1
.
5. From the outside of the chassis pull out the stems of the four push pins to release the
speakers then, remove the speaker
2
.
When installing the speakers, hold the plastic pin retainers firmly in place as they tend to be
pushed out of the chassis holes when the speaker is being positioned. Once a speaker mounting
hole has been properly aligned and the pin retainer pressed into it, insert the push pin to secure
the pin retainer. To ensure proper alignment, install the push pins in an X pattern.