IBM DTCA-24090 Hard Drive Specifications - Page 38

Acoustics

Get IBM DTCA-24090 - Travelstar 4.1 GB Hard Drive PDF manuals and user guides View all IBM DTCA-24090 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

5.6 Acoustics 5.6.1 Sound Power Level The criteria of A-weighted sound power level is described below. Measurements are to be taken in accordance with ISO 7779. The mean of 40 drives is to be less than the typical value. Each drive is to be less than the maximum value. Drives are to meet this requirement in both board down orientations. A-weighted Sound Power (Bels) Idle Operating Typical 3.3 3.6 Maximum 3.6 3.9 Background power levels of the acoustic test chamber for each octave band are to be recorded. Sound power tests are to be conducted with the drive supported by spacers so that the lower surface of the drive be located at 25 + / - 3mm height from the chamber floor. No sound absorbing material shall be used. The acoustical characteristics of the disk drive are measured under the following conditions. Idle mode : Power on, disks spinning, track following, unit ready to receive and respond to control line commands. Operating mode : Continuous random cylinder selection and seek operation of actuator with a dwell time at each cylinder. Seek rate for the drive can be calculated as shown below. Ns = 0.4/(Tt + T1) where: Ns : Average seek rate in seeks/s. Tt : Published seek time from one random track to another without including rotational latency. T1 : Equivalent time, in seconds, for the drive to rotate by half a revolution. 30 OEM Specifications of DTCA-2xxxx 2.5 inch H D D

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
5.6
Acoustics
5.6.1
Sound Power Level
The criteria of A-weighted sound power level is described below.
Measurements are to be taken in accordance with ISO 7779. The mean of 40 drives is to be less than the
typical value. Each drive is to be less than the maximum value. Drives are to meet this requirement in both
board down orientations.
Background power levels of the acoustic test chamber for each octave band are to be recorded.
Sound power tests are to be conducted with the drive supported by spacers so that the lower surface of the
drive be located at 25 + / - 3mm height from the chamber floor. No sound absorbing material shall be used.
The acoustical characteristics of the disk drive are measured under the following conditions.
Idle mode :
Power on, disks spinning, track following, unit ready to receive and respond to control line com-
mands.
Operating mode :
Continuous random cylinder selection and seek operation of actuator with a dwell time at each
cylinder. Seek rate for the drive can be calculated as shown below.
Ns =
0.4/(Tt +
T1)
where:
Ns
: Average seek rate in seeks/s.
Tt
: Published seek time from one random track to another without including rotational latency.
T1
: Equivalent time, in seconds, for the drive to rotate by half a revolution.
A-weighted Sound Power (Bels)
Typical
Maximum
Idle
3.3
3.6
Operating
3.6
3.9
30
OEM Specifications of DTCA-2xxxx 2.5 inch HDD