IBM DTCA-24090 Hard Drive Specifications - Page 60

Drive Address Setting - jumpers

Get IBM DTCA-24090 - Travelstar 4.1 GB Hard Drive PDF manuals and user guides View all IBM DTCA-24090 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

6.6 Drive Address Setting A jumper is available at the interface connector to determine the drive address. The set position of the jumper is as shown in Figure 35. Using Cable Selection, the drive address depends on the condition of pin 28 of the AT interface cable. In the case when pin 28 is ground or low, the drive is a Master. If pin 28 is open or high level, the drive is a Slave. Figure 35. Address setting by a jumper for DTCA-23240/24090. 6.6.1 Default Setting The default setting of jumper at shipment is No Jumper (Master). 52 OEM Specifications of DTCA-2xxxx 2.5 inch H D D

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
6.6
Drive Address Setting
A jumper is available at the interface connector to determine the drive address. The set position of the
jumper is as shown in Figure 35.
Using Cable Selection, the drive address depends on the condition of pin 28 of the AT interface cable. In the
case when pin 28 is ground or low, the drive is a Master. If pin 28 is open or high level, the drive is a Slave.
Figure 35. Address setting by a jumper for DTCA-23240/24090.
6.6.1
Default Setting
The default setting of jumper at shipment is No Jumper (Master).
52
OEM Specifications of DTCA-2xxxx 2.5 inch HDD