Intel S2600IP Service Guide - Page 57
If a power supply is installed, push the green latch in the direction shown while pulling out
 |
View all Intel S2600IP manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 57 highlights
Hardware Installations and Upgrades The power supply can be replaced if it fails. To replace the power supply, follow these steps: 1. Do one of the following: - If a filler panel is installed, use the 'finger hole' to remove the filler panel (see letter A). Figure 69. Removing the filler panel - If a power supply is installed, push the green latch in the direction shown while pulling out of the system by the handle. Figure 70. Removing the power supply module 2. Do one of the following: - Insert the power supply module into the power supply cage and push all the way until it clicks into place (see letter B). Figure 71. Installing the power supply module Intel® Server System R2000IP Service Guide 45
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52 -
53 -
54 -
55 -
56 -
57 -
58 -
59 -
60 -
61 -
62 -
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
 |
 |
Hardware Installations and Upgrades
Intel
®
Server System R2000IP Service Guide
45
The power supply can be replaced if it fails. To replace the power supply, follow these steps:
1.
Do one of the following:
-
If a filler panel is installed, use the 'finger hole' to remove the filler panel (see letter
A
).
Figure 69. Removing the filler panel
-
If a power supply is installed, push the green latch in the direction shown while pulling out
of the system by the handle.
Figure 70. Removing the power supply module
2.
Do one of the following:
-
Insert the power supply module into the power supply cage and push all the way until it
clicks into place (see letter
B
).
Figure 71. Installing the power supply module