Intel SR1670HV Service Guide - Page 45

SATA/SAS BackPlane Replacement

Get Intel SR1670HV - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858210034
View all Intel SR1670HV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

System Service 3. Reinstall the chassis cover. Press down gently on the location above the system fans to ensure proper fan installation as shown in the following figure. Figure 48. Restoring the Chassis Cover 4.3 SATA/SAS BackPlane Replacement The system includes a single SATA/SAS backplane that is mounted to the back side of the hard disk drive (HDD) bay module. You can replace the backplane replacement by performing the following procedure: 1. Remove the system top cover. 2. Remove all hard disk drive assemblies from the drive bays. NOTE: It is important to label each hard drive with the location from which it was taken from. You must return hard drives to the same place from which they were taken once you complete the backplane replacement procedure. 3. The HDD bay module is held in place by six screws, three on each side of the chassis. Remove all six screws. Figure 49. Screws On Hard Disk Drive Bay Module 4. Slide the HDD bay module forward approximately ½ inch (1.27cm) and lift front edge of module from alignment guide slots. Figure 50. Sliding the Hard Disk Drive Bay Module 30 Intel® Server System SR1670HV Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
System Service
30
Intel
®
Server System SR1670HV Service Guide
3.
Reinstall the chassis cover. Press down gently on the location above the system fans
to ensure proper fan installation as shown in the following figure.
Figure 48. Restoring the Chassis Cover
4.3
SATA/SAS BackPlane Replacement
The system includes a single SATA/SAS backplane that is mounted to the back side of the
hard disk drive (HDD) bay module. You can replace the backplane replacement by
performing the following procedure:
1. Remove the system top cover.
2.
Remove all hard disk drive assemblies from the drive bays.
NOTE:
It is important to label each hard drive with the location from which it was taken from.
You must return hard drives to the same place from which they were taken
once
you complete
the backplane replacement procedure.
3.
The HDD bay module is held in place by six screws, three on each side of the
chassis. Remove all six screws.
Figure 49. Screws On Hard Disk Drive Bay Module
4.
Slide the HDD bay module forward approximately ½ inch (1.27cm) and lift front
edge of module from alignment guide slots.
Figure 50. Sliding the Hard Disk Drive Bay Module