Intermec CV41 CV41 Vehicle Mount Computer (Windows Embedded Standard) User Man - Page 105

Troubleshoot Reading Bar Codes, Diags, Start Ping, Global

Get Intermec CV41 PDF manuals and user guides View all Intermec CV41 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Chapter 7 - Troubleshoot and Maintain the Computer 4 Tap the Diags tab to run a ping test to the host. a In the text field, enter the IP address of the host. b Tap Start Ping. The graph shows the amount of time it takes for the host to return the ping. 5 Tap the Global tab to view the global property values of the Wi-Fi connection. Troubleshoot Reading Bar Codes Use this section to troubleshoot problems that may prevent you from being able to read a bar code with an Intermec scanner. If you cannot find the solution in the following table, refer to your scanner user guide for more information. Problems Reading Bar Codes Problem Solution You cannot see the illumination • You may be too far away from the bar code label. Try moving beam or frame from the scanner closer to the bar code label and scan it again. when you press the Scan button • You may be reading the bar code label "straight on." Change and aim the imager at a bar code the reading angle and try again. label. • The imager hardware trigger might be disabled in Intermec Settings. To check the setting go to Intermec Settings and select Data Collection > Scanner Settings. Hardware trigger should be checked. CV41 Vehicle Mount Computer (Windows Embedded Standard) User Manual 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
Chapter 7 — Troubleshoot and Maintain the Computer
CV41 Vehicle Mount Computer (Windows Embedded Standard) User Manual
93
4
Tap the
Diags
tab to run a ping test to the host.
a
In the text field, enter the IP address of the host.
b
Tap
Start Ping
. The graph shows the amount of time it takes
for the host to return the ping.
5
Tap the
Global
tab to view the global property values of the Wi-Fi
connection.
Troubleshoot Reading Bar Codes
Use this section to troubleshoot problems that may prevent you from
being able to read a bar code with an Intermec scanner. If you cannot
find the solution in the following table, refer to your scanner user
guide for more information.
Problems Reading Bar Codes
Problem
Solution
You cannot see the illumination
beam or frame from the scanner
when you press the
Scan
button
and aim the imager at a bar code
label.
•
You may be too far away from the bar code label. Try moving
closer to the bar code label and scan it again.
•
You may be reading the bar code label “straight on.” Change
the reading angle and try again.
•
The imager hardware trigger might be disabled in Intermec
Settings. To check the setting go to Intermec Settings and
select
Data Collection > Scanner Settings
. Hardware
trigger should be checked.