Lenovo NetVista Hardware Maintenance Manual (HMM) for NetVista 2284 systems - Page 71

Index of Symptoms, Messages, Error Codes, or, or Beeps

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

- Check all adapter card jumper settings. - Check all adapter card switch settings. - Check all adapter card cables and connectors. Make sure that all of the above are set correctly and show the correct voltages and continuity. Replace any defective cables or adapter cards. See "Parts/Test Point Locations" on page 107. - Run the Diagnostics \ All Tests again. - If an error or other symptom is displayed, go to "Index of Symptoms, Messages, Error Codes, or Beeps" on page 38. - If no error can be detected or the symptom is intermittent, go to "Undetermined Problems" on page 74. • End 009 • If the last test stops and you cannot continue, first make sure all switches, power connectors, cables, and jumpers are set correctly and show the correct voltages and continuity. • Take note of any messages, error codes, beeps, or new symptoms. Go to "Index of Symptoms, Messages, Error Codes, or Beeps" on page 38. • If there is no error symptom or the error symptom is intermittent, go to "Undetermined Problems" on page 74. Check Procedures 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
Check Procedures
37
-
Check all adapter card jumper settings.
-
Check all adapter card switch settings.
-
Check all adapter card cables and connectors.
Make sure that all of the above are set correctly
and show the correct voltages and continuity. Re-
place any defective cables or adapter cards. See
“Parts/Test Point Locations” on page 107.
-
Run the Diagnostics \ All Tests again.
-
If an error or other symptom is displayed, go to
“Index of Symptoms, Messages, Error Codes, or
Beeps” on page 38.
-
If no error can be detected or the symptom is in-
termittent, go to “Undetermined Problems” on
page 74.
•
End
009 -
•
If the last test stops and you cannot continue, first
make sure all switches, power connectors, cables,
and jumpers are set correctly and show the correct
voltages and continuity.
•
Take note of any messages, error codes, beeps, or
new symptoms. Go to “Index of Symptoms,
Messages, Error Codes, or Beeps” on page 38.
•
If there is no error symptom or the error symptom
is intermittent, go to “Undetermined Problems” on
page 74.