Lenovo ThinkServer RD240 Hardware Maintenance Manual
Lenovo ThinkServer RD240 Manual
 |
View all Lenovo ThinkServer RD240 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lenovo ThinkServer RD240 manual content summary:
- Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 1
ThinkServer RD240 Hardware Maintenance Manual Machine Types: 1045, 1046, 1047, and 1048 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 2
on page iii • Appendix C "Notices" on page 137 Seventh Edition (March 2012) © Copyright Lenovo 2010, 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 3
, and serviceability 11 Chapter 5. Diagnostics 13 Troubleshooting tables 13 DVD drive problems 13 General problems 14 Hard disk drive problems 14 Intermittent problems 15 Keyboard, mouse, or pointing-device problems 15 Memory problems 16 Microprocessor problems 17 Monitor problems 17 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 4
program 129 Appendix A. RAID battery card assembly 131 Specifications 131 Battery life and data retention time . . . . . 131 Appendix B. Getting information, help, and service 133 Information resources 133 Using the documentation 133 ThinkServer Web site 133 Lenovo Support Web site 133 Help - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 5
käyttöä. Avant d'utiliser le produit, veillez à bien lire et comprendre les instructions de sécurité multilingues figurant sur le DVD de documentation fourni avec le produit. veiligheidsinstructies op de documentatie-dvd van het product hebt gelezen en begrijpt. © Copyright Lenovo 2010, 2012 iii - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 6
understand all caution and danger statements in this document before you perform the procedures. Read and understand any additional safety information that comes with the server or optional device before you install, remove, or replace the device. iv ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 7
telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. • Connect and disconnect cables as Dispose of the battery as required by local ordinances or regulations. © Copyright Lenovo 2010, 2012 v - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 8
of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other all power cords are disconnected from the power source. vi ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 9
a problem with one of these parts, contact a service technician. Statement 9 CAUTION: To avoid personal injury, disconnect the hot-swap fan cables before removing the fan from the device. Statement 10 CAUTION: The following label indicates sharp edges, corners, or joints nearby. © Copyright Lenovo - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 10
for electrical specifications. Statement 13 CAUTION: Make sure that the rack is secured properly to avoid tipping when the server unit is extended. Statement 14 CAUTION: Some accessory or option are disconnected at the dc power input terminals. viii ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 11
shock or energy hazards: • This equipment must be installed by trained service personnel in a restricted-access location, as defined by the NEC and on top of rack-mounted devices. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. © Copyright Lenovo 2010, 2012 ix - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 12
Statement 20 CAUTION: The battery is a lithium ion battery. To avoid possible explosion, do not burn the battery. Exchange it only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations. x ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 13
page 1 Introduction This Hardware Maintenance Manual for your Lenovo® ThinkServer® product contains information about the server features, specifications, component locations, configuration instructions, hardware replacement procedures, parts listing, and troubleshooting and diagnostics. Note: The - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 14
with your server and help you use, configure, and maintain your server. • Rack Installation Instructions This document provides instructions on how to install your server into a standard rack cabinet by using the rail kit shipped with the server. 2 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 15
maintain your server RAID and related devices. This document is in English only. Document only for trained service personnel The following document is intended only for trained service personnel of Lenovo. Hardware Maintenance Manual This document provides diagnostic information, parts listing, and - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 16
4 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 17
Install the server in the rack The Rack Installation Instructions manual is printed and also included on the documentation DVD. Connect the Ethernet cable "Rear view" on page 27 and power cord Turn on the server to verify operation "Turning on the server" on page 91 Review the BIOS settings and - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 18
6 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 19
system, platform firmware, and external devices. • EasyStartup DVD: The ThinkServer EasyStartup program guides you through the configuration of the hardware, the RAID controller, and the installation of the operating system and device drivers. • Integrated network support: The server comes with two - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 20
the Setup Utility program" on page 111. For a list of the supported microprocessors for your server, go to http://www.lenovo.com/thinkserver. On the ThinkServer systems page, click Products ➙ Options ➙ ThinkServer Processors. Memory modules: • Minimum system memory: 2 GB • Maximum system memory: 64 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 21
. Software programs Lenovo provides software to help get your server up and running. EasyStartup The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported Microsoft® Windows® and Linux operating systems and device drivers on your server. The EasyStartup - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 22
10 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 23
for system-management features and monitoring • System-error light-emitting diode (LED) on the front panel • Vital product data (VPD), including the serial number information and replacement part numbers, stored in the nonvolatile memory for easier remote maintenance © Copyright Lenovo 2010, 2012 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 24
12 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 25
to help you solve problems that might occur in the server. If you cannot diagnose and correct a problem by using the information in this chapter, see Appendix B "Getting information, help, and service" on page 133 for more information. Troubleshooting tables Use the troubleshooting tables to find - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 26
a similar trained service technician. problem has occurred. Hard disk drive problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See the parts listing in Chapter 8 "Parts listing, RD240 Types 1045, 1046, 1047, and 1048 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 27
Web site at http://www.lenovo.com/thinkserver. • The mouse or pointing-device cable is securely connected to the server. • The mouse or pointing-device device drivers are installed correctly. • The server and the monitor are turned on. • The mouse is enabled in the Setup Utility program. 2. If you - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 28
Setup Utility program. • All banks of memory are enabled. The server might have automatically disabled a memory bank when it detected a problem, or a memory bank might have been manually disabled. 2. Check the POST event log for DIMM error messages: • If a DIMM was disabled by a systems-management - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 29
. 4. (Trained service technician only) Replace the system board. Microprocessor problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See the parts listing in Chapter 8 "Parts listing, RD240 Types 1045, 1046, 1047, and - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 30
with the correct language (see Updating the firmware). 2. Reseat the monitor. 3. Replace the following components one at a time, in the order shown, restarting the server each time: a. Monitor b. (Trained service technician only) System board 18 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 31
problem is solved. • See the parts listing in Chapter 8 "Parts listing, RD240 Types 1045, 1046 server. For a list of the supported options for your server, go to http://www.lenovo.com/thinkserver. On the ThinkServer systems page, click Products ➙ Options. • You followed the installation instructions - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 32
the power cord and restart the server. 2. If the problem remains or if you are using an ACPI-aware operating system, suspect the system board. The server unexpectedly shuts See "Solving undetermined problems" on page 23. down, and the LEDs on the 20 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 33
b. Serial cable c. (Trained service technician only) System board Software problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See the parts listing in Chapter 8 "Parts listing, RD240 Types 1045, 1046, 1047, and 1048" on - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 34
(see "Solving undetermined problems" on page 23 for the minimum configuration). 4. Reconnect all ac power cords and turn on the server. If the server starts successfully, replace the adapters and devices one at a time until the problem is isolated. 22 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 35
" on page 21. Damaged data in CMOS memory or damaged firmware can cause undetermined problems. To reset the CMOS data, use the password switch 2 (SW4) to override the power-on password and clear the CMOS memory; see "Locating parts on the system board" on page 30. Check the LEDs on all the power - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 36
save and then clear the system-event log through the Setup Utility program. When you are troubleshooting, you might have to save and then clear the condition of the server. The first two conditions generally do not require that you restart the server. 24 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 37
to view the system-event log. The server is hung. You can restart the server and press Del to start the Setup Utility program and view the system-event onboard debug digitron helps trained service technicians to identify server problems. When you turn on the server, the onboard debug digitron will - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 38
26 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 39
server with eight hard disk drives and an optical drive shows the drives and parts on the front of the server. Figure 1. Front view of the server Rear view of the server shows the locations of the connectors and parts on the rear of the server. Figure 2. Rear view of the server 1 Power supply 1 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 40
expansion slot Front control panel This section provides information about the front control panel of the server. Front control panel helps you identify the connectors, controls, and LEDs on the front control Off ID is on. ID is off. Description 28 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 41
alarm • Temperature alarm LAN is active and data is being transferred. LAN is connected. LAN is not connected. LAN is active and data is being transferred. LAN is connected. LAN is not connected. Power is on. The server 1068E SAS RAID adapter and external 8708ELP SAS RAID adapter configurations - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 42
Left handle of the chassis Locating parts on the system board Figure 5 "Locating major parts on the system board" on page 31 and Figure 6 "Locating other connectors on the system board" on page 32 show the locations of the parts on the system board. 30 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 43
parts on the system board 1 Memory slot (CPU1 DIMM CHC0) 2 Memory slot (CPU1 DIMM CHB0) 3 Memory slot (CPU1 DIMM CHA0) 4 Memory slot (CPU1 DIMM CHA1) 5 Microprocessor (CPU1) 6 Power connector 2 (for CPU0) 7 24-pin power connector for the system board 8 Microprocessor (CPU0) 9 Memory RAID controller - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 44
is Disabled. Note: Before clearing the CMOS, turn off the server and disconnect the power cord. Move the jumper from pins 1-2 to pins 2-3. Wait more than five minutes and then move the jumper back to the normal position (pins 1-2) to clear CMOS. 32 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 45
Locating connectors on the backplane Backplane connector locations shows the connector locations on the backplane. Figure 7. Backplane connector locations 1 Mini SAS signal connector 2 2 Power connector 3 Mini SAS signal connector 1 Chapter 6. Locating parts, controls, LEDs, and connectors 33 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 46
34 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 47
levels of performance. To download firmware updates for your server, do the following: 1. Go to http://www.lenovo.com/support. 2. Click Download Drivers & Software and follow the instructions on the Web page to download firmware updates for your server. See "Updating the firmware" on page 128 for - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 48
the server cooling system works well. Leave approximately 50 mm (2 inches) of open space around the front and rear of the server. Do not place objects in front of the fans. For proper cooling and airflow, install the server cover before you turn on 36 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 49
halt, which might result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when you work inside the server with the power on. The server supports hot-swap devices and is designed to operate safely while it is turned on - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 50
instructions on how to install or remove a memory module. For a list of the supported memory modules for your server, go to http://www.lenovo.com/thinkserver. On the ThinkServer systems page, click Products ➙ Options ➙ ThinkServer Memory. Memory module installation rules Your server has eight memory - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 51
iii and "Guidelines" on page 35. This section provides instructions on how to install a memory module. To install a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 52
all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See Removing the server cover. 40 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 53
slot in the event that you later remove the device. • For a list of the supported hard disk drives for your server, go to http://www.lenovo.com/thinkserver. On the ThinkServer systems page, click Products ➙ Options ➙ ThinkServer Hard Drives. Removing the optical drive Attention: Do not open your - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 54
cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See Removing the server cover. 3. There is one screw on each side and two screws on screw on the rear bracket of the optical drive. 42 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 55
Figure 13. Removing the optical drive cage retaining screw 6. Slide out the optical drive cage with the optical drive. Figure 14. Sliding out the optical drive cage with the optical drive 7. Remove the two retaining screws that secure the optical drive in the cage. Then, slide the optical drive out - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 56
. • You have checked the instructions that come with the new optical drive to determine whether you must set any switches or jumpers in the drive. Note: If you are installing a drive that contains a laser, observe the following safety precautions. 44 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 57
result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or outlets and disconnect all cables that are connected to the server. 3. Remove the server cover. See Removing the server cover. 4. There is one screw on each side - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 58
Figure 16. Removing the drive access panel 5. Remove the retaining screw on the rear bracket of the optical drive. 46 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 59
Figure 17. Removing the optical drive cage retaining screw 6. Slide out the optical drive cage. Figure 18. Sliding out the optical drive cage 7. Remove the bezel of the optical drive cage. Chapter 7. Installing, removing, or replacing hardware 47 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 60
to any unpainted metal surface on the server. Then, remove the optical drive from the package and place it on a static-protective surface. 9. Follow the instructions that come with the optical drive to screws to secure the optical drive in the cage. 48 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 61
Figure 21. Securing the optical drive with screws 12. Slide the cage with the optical drive into place. Figure 22. Sliding the cage with the optical drive into place 13. Install the retaining screw to the rear of the cage to secure the optical drive cage in place. Chapter 7. Installing, removing, or - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 62
parts replacement. Removing a hot-swap hard disk drive Attention: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions ( 3 ). 50 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 63
This section provides instructions on how to install a hot-swap hard disk drive. This section applies only to server models that support hot-swap hard disk on the server. Then, remove the hard disk drive from the package. Note: The hot-swap hard disk drive server option for RD240 server is a fully - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 64
power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See Removing the server cover. 3. Disconnect any cables from the PCI card or any cables that impede access to the riser card. 52 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 65
of hardware, go to the appropriate section. • To complete the removal procedure, go to "Completing the parts replacement" on page 90. Installing the riser card assembly Attention: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 66
riser card to any unpainted metal surface on the server. Then, remove the riser card from the static-protective parts replacement" on page 90. Installing or removing a PCI card This section provides instructions on how to install or remove a PCI card. 54 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 67
section provides instructions on how to install a PCI card. Notes: • Depending on the server model, your server might look both for PCI cards only. The RAID card retention bracket 4 is for Lenovo RAID cards only. Some server models are not shipped with the RAID card retention bracket. Figure 28. - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 68
the server cover" on page 37. 3. Disconnect any cables from the PCI card or any cables that impede access to the riser card assembly. 4. Remove the riser card assembly together with the installed PCI card. See "Removing the riser card assembly" on page 52. 56 ThinkServer RD240 Hardware Maintenance - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 69
procedure, go to "Completing the parts replacement" on page 90. Installing, removing, or replacing hardware devices This section provides instructions on how to install, remove, or replace hardware devices for your server. You can maintain your server by replacing the failing hardware devices - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 70
reconfigure the server and Part Number instructions that come with the replacement battery. 1. Hold the system board battery 1 and position one side of the battery into its socket. Then, press the other side of the battery until it snaps into place. 58 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 71
time and passwords. See Starting the Setup Utility program for details. Removing or installing the RAID controller This section provides instructions on how to remove or install the RAID controller. Removing the RAID controller Attention: Do not open your server or attempt any repair before reading - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 72
"Completing the parts replacement" on page 90. Installing the ThinkServer 8708ELP SAS RAID Adapter Attention: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions on how to - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 73
from your server, place it in its original container. c. Check the appropriate support Web sites for the latest updates for your basic input/output system (BIOS) code, utility programs, device drivers, and other software applications. Follow the instructions provided by your Service Provider to - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 74
connector 3 J2 board-to-board connector Figure 35. Top view of the battery card assembly 1 Battery pack harness b. With the front side up, place the RAID controller on a flat, clean, static-free surface. 62 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 75
card assembly Note: There are three PCI card slots on the riser card assembly as shown in the illustration. The PCI card slot 1 2 is for RAID cards only. For more information about the PCI card slots, see "Installing a PCI card" on page 55. Chapter 7. Installing, removing, or replacing hardware 63 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 76
installation, go to "Completing the parts replacement" on page 90. • To reduce fan noise, the user can manually change the fan speed mode when using a ThinkServer 8708ELP SAS RAID Adapter without a ThinkServer 8708ELP SAS RAID Adapter Battery attached. For 64 ThinkServer RD240 Hardware Maintenance - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 77
from your server, place it in its original container. c. Check the appropriate support Web sites for the latest updates for your basic input/output system (BIOS) code, utility programs, device drivers, and other software applications. Follow the instructions provided by your Service Provider to - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 78
the battery card assembly to a PCI Express slot, center the Phillips-head screw driver to avoid damaging the screw head and do not over-tighten the screws as you the front side up, place the RAID controller on a flat, clean, static-free surface. 66 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 79
card assembly with the battery side up and the J5 board-to-board connector lining up with the J10 BBU connector 1 on the RAID controller. Carefully press the battery card assembly onto the RAID controller so that the two connectors are firmly joined. Then, secure the battery card assembly to the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 80
. The PCI card slot 1 2 is for RAID cards only. For more information about the PCI card slots, inches) mini SAS signal cables to the backplane of your server. Figure 45. Mini SAS signal connectors on the backplane parts replacement" on page 90. 68 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 81
from your server, place it in its original container. c. Check the appropriate support Web sites for the latest updates for your basic input/output system (BIOS) code, utility programs, device drivers, and other software applications. Follow the instructions provided by your Service Provider to - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 82
to a PCI Express slot, center the Phillips-head screw driver to avoid damaging the screw head and do not over-tighten remote connector (reserved for use) b. With the front side up, place the RAID controller on a flat, clean, static-free surface. 70 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 83
card assembly with the battery side up and the J1 board-to-board connector lining up with the J6B1 BBU connector 1 on the RAID controller. Carefully press the battery card assembly onto the RAID controller so that the two connectors are firmly joined. Then, secure the battery card assembly to the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 84
in the illustration. The PCI card slot 1 2 is for RAID cards only. For more information about the PCI card slots, see " 15.75 inches) mini SAS signal cables to the backplane of your server. Figure 50. Mini SAS signal cable connectors on the backplane a. ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 85
removal procedure, go to Completing the parts replacement. Installing the Ethernet card Attention: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions on how to install the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 86
to the server. 2. Remove the server cover. See Removing the server cover. 3. Slide the microprocessor fan duct a little bit backward to release the three plastic tabs from the chassis. Then, lift the microprocessor fan duct out of the chassis. 74 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 87
all cables that are connected to the server. 2. Remove the server cover. See Removing the server cover. 3. Place the microprocessor fan duct installation, go to Completing the parts replacement. Removing or installing the power supply This section provides instructions on how to remove or install - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 88
you suspect a problem with one of these parts, contact a service technician. To remove a power supply, do the following: 1. Press the tab 1 of the power supply and pull the handle 2 to slide the power supply out of the server. Figure 52. Removing the power supply 2. If you are instructed to return - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 89
server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. To - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 90
provides instructions on how to remove the heat sink. CAUTION: The heat sink might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover. To remove the heat sink, do the following: 78 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 91
the heat sink. Installing the heat sink Attention: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions on how to install the heat sink. Chapter 7. Installing, removing, or - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 92
outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See Removing the server cover. 3. Notice the orientation of the heat sink chassis 4. To complete the installation, go to Completing the parts replacement. 80 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 93
server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions server. 2. Remove the server cover. See Removing the server instructed to return the microprocessor, follow all packaging instructions - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 94
instructions on how to install the microprocessor. CAUTION: The heat sink and microprocessor might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server the pins while removing the cover. 82 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 95
2 in the microprocessor socket. Then, install the microprocessor into the socket. Figure 61. Installing the microprocessor 10. To complete the installation, go to Completing the parts replacement. Chapter 7. Installing, removing, or replacing hardware 83 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 96
. 8. Note the location of all cable connections on the system board and disconnect all cables. Locating parts on the system board. 9. Remove the nine screws that secure the system board to the chassis, following the sequence shown in the figure below: 84 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 97
Figure 62. Removing the nine screws that secure the system board 10. Carefully lift the system board out of the chassis. 11. Remove the microprocessor socket cover from the new system board. 12. Remove the microprocessor from the failing system board and install it on the new system board. 13. The - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 98
instructed to return the system board, follow all packaging instructions server and wait three to five minutes to let the server cool before removing the server cover. To install a system board after a failing system board is removed, do the following: 86 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 99
heat sink and a memory module. See Installing the heat sink and Installing a memory module. 5. Install the server cover. See Installing the server cover. 9. To complete the installation, go to Completing the parts replacement. Removing or installing the system fans This section provides instructions - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 100
chassis 2 . Note: Mind the system fan cables. Remove the cables from any clip before removing the system fans. Figure 64. Removing the system fans 88 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 101
: Do not open your server or attempt any repair before reading and understanding the "Safety information" on page iii and "Guidelines" on page 35. This section provides instructions on how to install the system fans. CAUTION: Hazardous moving parts. Keep fingers and other body parts away. To install - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 102
server cover is secured by a thumbscrew, for safety consideration, be sure to use a tool, for example a screw driver, to tighten the thumbscrew and always make sure that the thumbscrew is securely installed. Also, do not over-tighten the thumbscrew. 90 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 103
the operating system does not run, and all core logic except for the service processor (the integrated management module) is shut down; however, the server can respond to requests to the service processor, such as a remote request to turn on the server. The power-on LED flashes to indicate that the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 104
. To obtain a copy of the publications, go to: http://www.lenovo.com/support 2. Turn off the server and all attached devices. 3. Follow the instructions that come with the device to prepare it for installation and to connect it to the server. 92 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 105
ThinkServer RD240 Types 1045, 1046, 1047, and 1048 servers. To check for an updated parts listing on the Web, complete the following steps: 1. Go to http://www.lenovo.com/support. 2. Click Download & Drivers ➙ ThinkServer and then follow the instructions on the Web page to download firmware updates - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 106
and getting service and assistance, see the Warranty and Support Information document. The following table lists the part numbers for the server components. Table 10. Parts listing, CTO) 90Y1394 71Y9029 46R6632 46U3187 71Y9037 71Y9039 71Y9045 94 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 107
1) 46U3436 46U3437 46U3438 46U3439 46U3400 03X3623 46U3440 46U3519 CRU part number (Tier 2) FRU part number 71Y9041 71Y9043 71Y9047 71Y9049 03X3645 03X3646 03X3647 03X3648 03X3649 03X3650 03X3651 71Y9031 46U3453 46U3276 46U3353 Chapter 8. Parts listing, RD240 Types 1045, 1046, 1047, and 1048 95 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 108
) Riser card assembly (models CTO all models) Heat sink, 80/95W (models CTO all models) Memory DIMM, 2 GB DDR3 RDIMM 1333 MHz (models CTO 11U 11G) CRU part number (Tier 1) 46U3527 46U3605 46U3277 46U3442 CRU part number (Tier 2) FRU part number 96 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 109
Table 11. Parts listing, Type 1046 (continued) Index 4 4 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 Description Memory DIMM, 4 GB DDR3 RDIMM 1333 MHz (models CTO 12U 12G 13U 13G 14U 15G 16G 17U 17G 18U 18G 19U 19G 1AU 1AG 1BU 1BG) Memory DIMM, 8 GB DDR3-1333 RDIMM (models CTO 1CU 1CG 1DU 1DG) Power - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 110
Parts listing, Type 1046 1BG 1CU 1CG 1DU Server rail kit (models CTO all models Screw kit (models CTO all models) LSI MegaRAID 8708E SAS RAID part number (Tier 2) FRU part number 03X3650 03X3651 46U3453 46U3276 46U3353 46U3522 46U3558 46U3524 46U3526 98 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 111
Parts listing, Type 1046 (continued) Index Description LSI 3801E SAS HBA (models CTO) Emulex LPe1150 4Gb (models CTO) Emulex LPe111-E 4Gb (models CTO) LSI 8708EM2 8 ports 256MB SAS RAID Card (models CTO) LSI iBBU06 battery unit for 8708EM2 (models CTO 19U 19G 1AU 1AG 1CU 1CG 1DU 1DG) ThinkServer - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 112
CTO) CRU part number (Tier 1) 46U3436 46U3437 46U3438 46U3439 46U3400 03X3623 46U3440 CRU part number (Tier 2) FRU part number 71Y9041 71Y9043 71Y9047 71Y9049 03X3645 03X3646 03X3647 03X3648 03X3649 03X3650 03X3651 71Y9031 46U3276 46U3453 46U3353 100 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 113
(models CTO) 03X3620 ThinkServer RAID 700 Adapter (models CTO) 03X3617 ThinkServer RAID 700 Battery (models CTO) 03X3618 Intel PRO/1000PT dual ports Ethernet card (models CTO) 630 mm MiniSAS-MiniSAS SAS cable (QTY 2) (models CTO all models) 67Y1430 03X3631 CRU part number (Tier 2) FRU - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 114
Parts listing, Type 1048 (continued) Index 4 4 5 5 6 6 6 6 6 6 6 6 6 Description Memory DIMM, 4 GB DDR3 RDIMM 1333 MHz (models CTO 12U 15U) Memory DDR3-800, 80W (models CTO) 102 ThinkServer RD240 Hardware Maintenance Manual 71Y9049 03X3645 03X3646 03X3647 03X3648 03X3649 03X3650 03X3651 71Y9031 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 115
Server rail kit (models CTO all models) Screw kit (models CTO all models) LSI MegaRAID 8708E SAS RAID RAID card (models CTO) 46U3314 46U3315 03X3619 CRU part number (Tier 2) FRU part number 46U3276 46U3453 46U3353 46U3522 46U3558 46U3524 46U3526 Chapter 8. Parts listing, RD240 Types 1045, 1046 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 116
ThinkServer RAID 700 Adapter (models CTO) ThinkServer RAID 700 Battery (models CTO) Intel PRO/1000PT dual ports Ethernet card (models CTO) 630 mm MiniSAS-MiniSAS SAS cable (QTY 2) (models CTO all models) CRU part will be installed. Lenovo power cords for ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 117
(models CTO) 43N9029 Thailand (models CTO) Table 15. Power cords, Type 1046 Lenovo Power cord part number Used in these countries and regions 41R3184 US (models CTO 11U 12U CTO) 41R3196 Australia / New Zealand (models CTO) Chapter 8. Parts listing, RD240 Types 1045, 1046, 1047, and 1048 105 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 118
(models CTO) Table 17. Power cords, Type 1048 Lenovo Power cord part number Used in these countries and regions 41R3184 United States Lenovo ship group for a specific country or region are usually available only in that country or region. 106 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 119
Table 19. Ship group, Type 1046 Lenovo Ship group part number 03X3904 03X3905 90Y1174 90Y1176 90Y1177 Server 2008 Standard Edition (SP2) 64-bit (Spanish) (models CTO) Microsoft Windows Server 2008 R2 Standard Edition 64-bit (United States) (models CTO) Chapter 8. Parts listing, RD240 Types 1045, 1046 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 120
2008 R2 Standard Edition 64-bit (Italian) (models CTO) Microsoft Windows Server 2008 R2 Essentials Edition 64-bit (United States) (models CTO) Microsoft Windows Small Business Server 2008 Premium Edition (SP2) 64-bit (United States) (models CTO) 108 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 121
Edition 64-bit (Italian) (models CTO) Microsoft Windows Server 2008 R2 Essentials Edition 64-bit (United States) (models CTO) Microsoft Windows Small Business Server 2008 Premium Edition (SP2) 64-bit (United States) (models CTO) Chapter 8. Parts listing, RD240 Types 1045, 1046, 1047, and 1048 109 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 122
110 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 123
Utility (press Ctrl+H to start) MegaRAID Storage Manager (MSM) ThinkServer RAID 700 Adapter LSI MegaRAID WebBIOS Configuration Utility (press Ctrl+H to start) MegaRAID Storage Manager (MSM) Using the Setup Utility program Use the Setup Utility program to perform the following tasks: • View - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 124
Advanced PCIPnP Boot Security Chipset Exit Description Set the basic BIOS parameters. Set the advanced BIOS parameters. Set the PCI parameters. Set the boot parameters. Set the security parameters. Set the chipset. Exit the Setup Utility program. 112 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 125
BIOS version and creation date information. View microprocessor information. View memory Configuration. Remote Access Configuration the Remote Access ThinkServer 8708EM2 RAID Adapter with a ThinkServer 8708EM2 RAID Battery attached or a ThinkServer 8708ELP SAS RAID Adapter with a ThinkServer 8708ELP SAS RAID - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 126
from using the data page. Enable or disable the hyper-thread technology. (Whether your server supports this feature or not is depending on the type of the installed microprocessor.) Enable or or disable the C3 State Demotion of the microprocessor. 114 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 127
Configure SATA as [IDE]RAID To select the hard Setup Utility program. 2. The SATA Configuration item might not apply because your server Support DisabledEnabled[Auto] Enable or disable the support on the hot-swap USB diskette drive. Note: The settings in [ ] are the default settings in the Setup - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 128
the fan alarm function. If the Setup Utility SUPPORT Disabled[Enabled] Description View the system event log. Delete the system event log. Set the IP address source, IP address, subnet mask, and gateway address. Enable or disable the PEF support. 116 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 129
Setup Utility program. Description Disable or enable the OS based dongle. If enabled, whenever any problems arising from the operation system, such as the system halted, the system management in the Setup Utility program. Description Enable or disable the serial port remote access. Table server 117 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 130
[Enabled]Disabled AddOn ROM Display Mode [Force BIOS]Keep Current Bootup Num-Lock [Off]On Boot the Num-Lock LED state. Set the startup device sequence (support at most five startup devices). Based on the installed hard disk Setup Utility program. 118 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 131
memory module. Make sure that the mandatory memory frequency setting is less than the maximum frequency that the memory module can support. Memory Mode [Independent]Channel MirroringLockstep Set the memory Setup Utility program, you can set a password to prevent unauthorized access to your server - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 132
with all factory-supported RAID controllers • Automatically detects hardware and lists all supported RAID configurations Location ThinkServer EasyStartup DVD Where to find more information "Using the ThinkServer EasyStartup program" on page 121 120 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 133
can be used to configure RAID controllers on similarly configured Lenovo servers. Onboard 1068E SAS RAID Press Ctrl+C to start adapter LSI MegaRAID WebBIOS Configuration Utility ThinkServer 8708ELP SAS RAID adapter, ThinkServer 8708EM2 RAID Adapter, or ThinkServer RAID 700 Adapter (9260-8i) Press - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 134
RAID controllers, operating systems, and server configurations supported by that version of the EasyStartup program. 4. Click User Guide. The User Guide and then you will be presented with the Lenovo License Agreement. Read the license agreement carefully. ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 135
RAID The RAID configuration feature that is part of the EasyStartup program enables you to view and change RAID settings for supported RAID the end of the installation process and install ThinkServer EasyManage software to help you manage your servers. • Install Windows components: This task enables - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 136
Connecting mini-SAS cable Your server comes with a 200 mm (7.87 inches) mini SAS cable with four SAS connectors and one SGPIO connector. mini-SAS signal cable connector on the backplane, refer to "Locating connectors on the backplane" on page 33. 124 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 137
view the controller list, view the hard disk drive information, and configure RAID. When working with this program, you must use the keyboard. The keys PCI device or function assigned to the adapter The current firmware version Indicating whether the adapter on the boot list is the server 125 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 138
the adapter MPT Firmware Revision The current firmware version SAS Address the BIOS, instead of the driver on the operating system. This option might not be supported by RAID Properties Set the Host RAID. See "SAS RAID settings" on page 127. 126 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 139
RAID 1 as an example to guide you to create or delete SAS RAID using the LSI Configuration Utility program. Creating the RAID 1 array This section provides instructions on how to create RAID 1 using the LSI Configuration Utility program. To create RAID 1, do the following: 1. In the SAS RAID setup - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 140
. • The integrated SAS controller firmware is stored in the ROM of SAS controller on the system board. • The SAS RAID card firmware is stored in ROM on the SAS RAID card. The Ethernet firmware is downloadable at http://www.lenovo.com/support. 128 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 141
date and helps you avoid unnecessary outages. Firmware Updater updates the server system and adapter firmware. To update your system, do the following: 1. Go to http://www.lenovo.com/support. 2. Click Download & Drivers ➙ ThinkServer and then follow the instructions on the Web page to download the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 142
130 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 143
ThinkServer 8708EM2 SAS RAID Controller Battery) 6.6 inches x 2.536 inches (ThinkServer RAID 700 Battery) 1350 mAh (ThinkServer 8708ELP SAS RAID Controller Battery) 700 mAh (ThinkServer 8708EM2 SAS RAID Controller Battery) 1590 mAh (ThinkServer RAID 700 as follows: © Copyright Lenovo 2010, 2012 131 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 144
Mx16 DDR2 DRAMs (low power) ThinkServer 8708EM2 SAS RAID Controller Battery 72 hours for 256 Mbytes, using three 64 Mx16 DDR2 DRAMs (low power) ThinkServer RAID 700 Battery (iBBU08) 72 hours through • DRAM (dynamic random access memory) size 132 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 145
Refer to the troubleshooting information in your server User Guide for instructions on how to diagnose problems and do basic troubleshooting. The troubleshooting and diagnostics information might tell you that you need additional or updated device drivers or other software. Lenovo maintains pages on - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 146
Firmware Interface (UEFI) BIOS as part of an installation or upgrade • Changes, modifications, or upgrades to device drivers • Installation and maintenance of network operating systems (NOS) • Installation and maintenance of application programs 134 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 147
. To determine whether your computer is eligible for International Warranty Service and to view a list of the countries where service is available, go to http://www.lenovo.com/support, click Product & Service Warranty, and follow the instructions on the Web page. For technical assistance with the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 148
136 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 149
of any other product, program, or service. Lenovo may have patents or pending patent applications for use in implantation or other life support applications where malfunction may result in materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 150
after handling. Recycling information Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in 138 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 151
their instructions. If you use a Lenovo computer service manual for specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 152
and treatment, go to: http://www.lenovo.com/recycling Requirement for batteries containing Management Practices for Perchlorate Materials. This product/part may include a lithium manganese dioxide battery which contains a perchlorate substance. 140 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 153
that the levels of particulates or gases in your environment have caused damage to the server, Lenovo may condition provision of repair or replacement of servers or parts on implementation of appropriate remedial measures to mitigate such environmental contamination. Implementation of such remedial - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 154
due to the presence of hazardous substances. For additional WEEE information go to: http://www.lenovo.com/recycling Le marquage des déchets d'équipements électriques et électroniques (DEEE) s'applique , recupero del WEEE e minimizzare qualsiasi 142 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 155
kunnen hebben op het milieu en de volksgezondheid, tot een minimum te beperken. Voor meer informatie over WEEE gaat u naar: http://www.lenovo.com/recycling. WEEE-mærkningen (Waste Electrical and Electronic Equipment) gælder kun for lande i EU samt Norge. Udstyr mærkes i henhold til EU's direktiv - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 156
eventuell skadelig virkning av elektrisk og elektronisk utstyr på miljø og helse, som skyldes skadelige stoffer. Du finner mer informasjon om WEEE på denne adressen: http://www.lenovo.com/recycling. 144 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 157
Restriction of Hazardous Substances Directive (RoHS) This topic provides statements about the Restriction of Hazardous Substances Directive (RoHS). China RoHS Appendix C. Notices 145 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 158
refers to the Lenovo ThinkServer machine types 1045, 1046, 1047, installed and used in accordance with the instruction manual, may cause harmful interference to radio operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 159
of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 160
which connect to the power mains with rated current less than or equal to 20 A per phase China Class A compliance statement Taiwan Class A compliance statement Lenovo product service information for Taiwan 148 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 161
-swap, removing 50 © Copyright Lenovo 2010, 2012 DVD drive problems 13 error symptoms 13 E EasyStartup using 121 electrical input 9 environment 8 error symptoms CD-ROM drive, DVD-ROM drive 13 general 14 hard disk drive 14 intermittent 15 keyboard, non-USB 15 memory 16 microprocessor 17 monitor 17 - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 162
SATA Adapter ThinkServer RAID 700 69 SAS/SATA controller 60 SAS/SATA controller 8708EM2 65 server cover 90 system board battery 58 system fans 89 integrated functions 8 integrated network support 7 intermittent problems 15 internal drives 150 ThinkServer RD240 Hardware Maintenance Manual installing - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 163
port problems 21 server turn off 91 turn on 91 server components 30 server configuration, updating 111 server cover installing 90 removing 37 server cover, reinstalling 90 server documentation 1 server firmware, BIOS 7 server replaceable units 94 service, getting 133 serviceability 11 Setup Utility - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 164
passwords 119 Setup Utility program 111 V video problems 17 video controller, integrated specifications 8 viewing event logs 24 W Web site compatible options 38 Lenovo support 93 publication ordering 133 working inside the server with the power on 37 152 ThinkServer RD240 Hardware Maintenance Manual - Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 165
- Lenovo ThinkServer RD240 | Hardware Maintenance Manual - Page 166
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
 |
 |
ThinkServer RD240
Hardware Maintenance Manual
Machine Types: 1045, 1046, 1047, and 1048