Lenovo ThinkServer RD240 Hardware Maintenance Manual - Page 28

Memory problems, Reseat the DIMMs.

Get Lenovo ThinkServer RD240 PDF manuals and user guides View all Lenovo ThinkServer RD240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See the parts listing in Chapter 8 "Parts listing, RD240 Types 1045, 1046, 1047, and 1048" on page 93 to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). • If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service technician. Symptom Action 3. Replace the following components one at a time, in the order shown, restarting the server each time: a. Mouse or pointing device b. (Trained service technician only) System board Memory problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See the parts listing in Chapter 8 "Parts listing, RD240 Types 1045, 1046, 1047, and 1048" on page 93 to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs). • If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service technician. Symptom Action The amount of system memory that is displayed is less than the amount of installed physical memory. 1. Make sure that: • No error LEDs are lit on the operator information panel or on the DIMM. • Memory mirroring does not account for the discrepancy. • The memory modules are seated correctly. • You have installed the correct type of memory. • If you changed the memory, you updated the memory configuration in the Setup Utility program. • All banks of memory are enabled. The server might have automatically disabled a memory bank when it detected a problem, or a memory bank might have been manually disabled. 2. Check the POST event log for DIMM error messages: • If a DIMM was disabled by a systems-management interrupt (SMI), replace the DIMM. • If a DIMM was disabled by the user or by POST, run the Setup Utility program and enable the DIMM. 3. Make sure that there is no memory mismatch when the server is at the minimum memory configuration. 4. Add one pair of DIMMs at a time, making sure that the DIMMs in each pair are matching. 5. Reseat the DIMMs. 6. Replace the DIMMs in step 5 on page 16, one at a time, in the order shown, restarting the server each time. Multiple rows of DIMMs in a branch are identified as failing. 1. Reseat the DIMMs; then, restart the server. 2. Replace the lowest-numbered DIMMs with identical known good DIMMs; then, restart the server. Repeat as necessary. If the failures continue after all identified pairs are replaced, go to step 4 on page 17. 16 ThinkServer RD240 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
•
Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.
•
See the parts listing in Chapter 8 “Parts listing, RD240 Types 1045, 1046, 1047, and 1048” on page 93 to
determine which components are customer replaceable units (CRUs) and which components are field
replaceable units (FRUs).
•
If an action step is preceded by “(Trained service technician only),” that step must be performed only by
a trained service technician.
Symptom
Action
3. Replace the following components one at a time, in the order shown, restarting
the server each time:
a.
Mouse or pointing device
b. (Trained service technician only) System board
Memory problems
•
Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.
•
See the parts listing in Chapter 8 “Parts listing, RD240 Types 1045, 1046, 1047, and 1048” on page 93 to
determine which components are customer replaceable units (CRUs) and which components are field
replaceable units (FRUs).
•
If an action step is preceded by “(Trained service technician only),” that step must be performed only by
a trained service technician.
Symptom
Action
The amount of system memory
that is displayed is less than
the amount of installed physical
memory.
1. Make sure that:
•
No error LEDs are lit on the operator information panel or on the DIMM.
•
Memory mirroring does not account for the discrepancy.
•
The memory modules are seated correctly.
•
You have installed the correct type of memory.
•
If you changed the memory, you updated the memory configuration in the
Setup Utility program.
•
All banks of memory are enabled. The server might have automatically
disabled a memory bank when it detected a problem, or a memory bank
might have been manually disabled.
2. Check the POST event log for DIMM error messages:
•
If a DIMM was disabled by a systems-management interrupt (SMI), replace
the DIMM.
•
If a DIMM was disabled by the user or by POST, run the Setup Utility program
and enable the DIMM.
3. Make sure that there is no memory mismatch when the server is at the minimum
memory configuration.
4. Add one pair of DIMMs at a time, making sure that the DIMMs in each pair
are matching.
5. Reseat the DIMMs.
6. Replace the DIMMs in step 5 on page 16, one at a time, in the order shown,
restarting the server each time.
Multiple rows of DIMMs in a
branch are identified as failing.
1. Reseat the DIMMs; then, restart the server.
2. Replace the lowest-numbered DIMMs with identical known good DIMMs;
then, restart the server. Repeat as necessary. If the failures continue after all
identified pairs are replaced, go to step 4 on page 17.
16
ThinkServer RD240 Hardware Maintenance Manual