LiftMaster 61LM Owners Manual - Page 256

OWNER'S MANUAL WARNING To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: CAUTION • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. AVERTISSEMENT The 972-315LM remote control can activate two separate residential or commercial garage door openers and/or gate openers. The instructions for programming garage door openers are illustrated below. Please refer to the original receiver ATTENTION programming for commercial and gate products. Both push buttons are factory programmed to work with Security✚ receivers having an orange "learn" button. The rolling code between these channels and the receiver changes with each use, randomly accessing over 100 billion new codes. As an added feature, the push button on the right is capable of learning or being trained to duplicate or match another CGI manufactured fixed code or billion-code remote. This feature is normally used when several remotes are required to operate one fixed code device such as a gate opener or commercial dock door. In this case, the code transmitted to the receiver remains constant or fixed, not using the Security✚ format. NOTE: The push button on the left cannot be changed from Security✚, only the right button is trainable. Model 972-315LM Security✚ 2 Channel Remote Control WARNING Instructions are Described and Illustrated Below If you have a lighted push button that looks like the lighted push button illustrated follow the instructions below. 1. Remove the cover from the Lighted Door Control. WARNING 2. Press and hold the button on the hand-held remote that you wish to operate your garage door. 3. While holding the remote button, press and hold the "A" button on the Lighted Door Control. AVERTISSEMENT "A" 4. Continue holding both buttons while you Button AVERTISSEMENT press the "B" button on the Lighted Door Control (all three buttons are held). "B" Button 5. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. If you have a multi-function wall control follow instructions below. 1. Press and hold the button on the hand-held remote that you wish to operate your garage door. 2. While holding the remote button, press and hold the light button on the Multi-Function Door Control. LOCK LIGHT Right Push Button (Multi-use) The Remote Control Batteries WARNING To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. CAUTION • If battery is swallowed, immediately notify doctor. The lithium batteries should produce power for up to 5 years. To replace, pry open case with visor clip or screwdriver, as shown. Insert batteries positive side up (+). Dispose of old batteries properly. AVERTISSEMENT NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the ATTENTION following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3. Continue holding both buttons while you press the push bar on the Multi-Function Door Control (all three buttons are held). LOCK LIGHT 4. Release buttons when the motor unit lights blink. It has learned the code. If light WARNING bulbs are not installed, two clicks will be heard. If neither of the two programming instructions match your type and style of opener follow instructions below. WARNING Press and release the "learn" button on the motor unit. The learn indicator light will glow steadily for 30 seconds. Within 30 seconds, press and hold the button on the hand-held remote. Release the button when the motor unit light blinks. It has learned the code. If light bulbs are not installed, two clicks will be heard. To Erase All Codes From Motor Unit Memory AVERTISSEMENT To deactivate any unwanted remote, first erase all codes: Press and hold the "learn" button on motor unit until the learn indicator light goes out (approximately 6 seconds). All previous codes AVERTISSEMENT are now erased. Reprogram each remote or key- less entry you wish to use.