LiftMaster 61LM Owners Manual - Page 262
Model 976-315LM Security, Wireless Keyless Entry
View all LiftMaster 61LM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 262 highlights
OWNER'S MANUAL Model 976-315LM Security✚ Wireless Keyless Entry WARNING To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: CAUTION • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. FEATURES AVERTISSEMENT For use with any Security✚ garage door openers having an orange "learn" button. ATTENTION Personalized Password: Up to 10,000 possible combinations. Password can be easily changed if desired. Temporary Password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries. Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes. Operation: Opener activates when 4-digit password and Enter button is pressed. If wrong numbers are accidentally pressed, correction can be made immediately. The Enter button will transmit only the last four digits. The Keypad will blink for 15 seconds after the password is transmitted. During that time the Enter button can be used to stop or reverse the door travel. THE KEYLESS ENTRY BATTERY WARNING To prevent possible SERIOUS INJURY or DEATH: CAUTION • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. The 9 volt battery should produce power for at least one year. Replace when the keypad illumination becomes dim. Dispose of old batAteriVesEproRpeTrlyI.SSEMENT ATTENTION NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING Instructions are Described and Illustrated Below If you have a lighted push button that looks like the lighted push button illustrated follow the instructions below. WARNING 1. Remove the cover from the Lighted Door Control. 2. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. AVERTISSEMENT 3. While holding the ENTER button, press and hold the "A" button on the Lighted Door Control. AVERTISSEMENT 4. Continue holding the ENTER and "A" Button "A" buttons while you press the "B" button on the Lighted Door Control (all three buttons are held). "B" Button 5. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. If you have a multi-function wall control follow instructions below. 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. LOCK LIGHT WARNING 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door WARNING Control (all three buttons are held). LOCK LIGHT 4. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. If neither of the two programming instructions match your AVERTISSEMENT type and style of opener follow instructions below. Press and release the "learn" button on motor unit. The learn indicator light will glow steadily for 30 seconds. Within AVERTISSEMENT 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button. Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. 1