Panasonic WJRT208 WJRT208 User Guide - Page 34
Descriptions and remarks, Selectable parameters, Default Setting], System setup SYSTEM SETUP, Full
View all Panasonic WJRT208 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 34 highlights
System setup (SYSTEM SETUP) Item "Power On Rec." Descriptions and remarks Recording will automatically start when the power is turned on. Selectable parameters [Default Setting] "On/Off" "Off" "Seq. Dwell" "Video Format" "Overwrite" "Status Display" "Keylock Time" "Keylock Buzz" "Alarm Buzz" "Pre Recording" "Rec. Quality" Sequential changeover time intervals. 02 - 30, 05 The video output format is fixed to the NTSC system. Therefore, the user "NTSC" cannot set the settings. Even when "On" is selected for "Overwrite", recording will not be per- "On/Off" formed to protect data from overwriting for the days set on "Rec. Reserve" "On" of "CAMERA SETUP" unless the set days have passed. It is possible to conceal information such as the channel name that is dis- "All/Stat/None/Name" played on the screen. "All" Even after the lapse of the preset time, the key lock does not function if 005 - 999 600 recording data is being backed up. After the lapse of the preset time counted after the completion of recording data backup, the key will be automatically locked. When setting is made at "On" and a password is wrongly keyed in three times continuously, the buzzer begins to sound for one minute. Buzzer "On/Off" is set up. "On/Off" "On" "On/Off" "Off" The time period for pre recording can differ according to the order of "On/Off" "Off" recording start. The minimum time period is 5 seconds. (Changeable with "I Frame Inter.", "Rec. Quality", and "Stream Type") When changing this setting, it is necessary to stop recording and discon- nect all network connections. Note: When Pre Recording is set at "On", the pre-recorded image data may be separated to different data groups. If settings of "Rec. Quality", "I Frame Inter.", "Stream Type", and "Frame Rate" are changed in the middle of recording, recording will stop and then will resume. Then the setting values become effective. If recording is not stopped, the new setting becomes effective after the lapse of the time period preset with "RECORD LENGTH". "SP Fine/Fine/Good/ Normal/Extended" "Normal" "I Frame Inter." "Resolution" "Alarm Spot" "Stream Type" "Terminal Input" "Frame Rate" Playback is delayed if the setting value for "I Frame Inter." is too high. We recommended using a default value. When changing this setting, it is necessary to stop recording and disconnect the network connections. Implement the settings of "I Frame Inter." after the pre-recording setting has been set at OFF. 01 - 15 04 Resolution of image data output from the VGA interface 800 x 600 or 1024 x 768 [800 x 600] When an alarm goes off, the screen of the occurring alarm is displayed in On/Off "Off" the single-spot mode. When the setting is made at "VBR", there may be a difference in recording CBR/VBR length. If the recording time need be in higher preference, the setting "CBR" should be made at "CBR". If screen changes seem to be extreme, the set- ting made at "VBR" is preferable. N.O.: Alarm is started with a low-level signal. N.C.: Alarm is started with a high-level signal. The frame rate set at "Full" is 25 frames/second. N.O./N.C. "N.O." "Full, 1/2F, 1/4F, 1/8F, 1/16F" "Full" Note: When "Terminal Input" is set at "N.C.", an alarm unit of "N.O." should be connected to the alarm port of this unit. If no connections are made, the alarm port will be "N.O." (normally open) and will continue receiving alarm signals at all times. 34