Sharp MX-2310U Installation Manual - Page 12

occur causing damage., When removing or installing the developing unit, put your hand

Get Sharp MX-2310U PDF manuals and user guides View all Sharp MX-2310U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3) While pressing the lever, pull out the developing unit to remove. 6) Install the cover. 7) Shake the developer unit horizontally a few times. 4) Open the cover to remove. Be sure to keep the developing unit level while supplying the developer. 8) Install the developer unit. 5) Loading developer to the developing units. Be sure to shake the bag of developer thoroughly before pouring into the developing unit. When pouring the developer into the unit, use care to not get developer in to the drive section. Slide the developing unit horizontally into the machine, in the direction of the arrow, until developing unit locks into. place. Do not push the unit diagonally, as contact with the drum may occur causing damage. When removing or installing the developing unit, put your hand from below the unit and slide it in parallel along the guide. At that time, be careful not to touch the roller surface. When installing the machine, there is no need to remove or install the OPC drum unit. If it must be removed or installed for any reason, follow the procedures below. When removing or installing the OPC drum unit, put your hand from below the unit and slide it in parallel along the guide on the right side. At that time, be careful not to touch the OPC drum surface. MX-2310U MX-2310U (MAIN UNIT) 2 - 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
MX-2310U
MX-2310U (MAIN UNIT)
2 – 3
3)
While pressing the lever, pull out the developing unit to
remove.
4)
Open the cover to remove.
5)
Loading developer to the developing units.
Be sure to shake the bag of developer thoroughly before pour-
ing into the developing unit.
When pouring the developer into the unit, use care to not get
developer in to the drive section.
6)
Install the cover.
7)
Shake the developer unit horizontally a few times.
Be sure to keep the developing unit level while supplying the
developer.
8)
Install the developer unit.
Slide the developing unit horizontally into the machine, in the
direction of the arrow, until developing unit locks into. place.
Do not push the unit diagonally, as contact with the drum may
occur causing damage.
When removing or installing the developing unit, put your hand
from below the unit and slide it in parallel along the guide.
At that time, be careful not to touch the roller surface.
When installing the machine, there is no need to remove or
install the OPC drum unit. If it must be removed or installed for
any reason, follow the procedures below. When removing or
installing the OPC drum unit, put your hand from below the unit
and slide it in parallel along the guide on the right side.
At that time, be careful not to touch the OPC drum surface.