Sharp MX-2310U Installation Manual - Page 41

F. Image off-center adjustment, MX-DE12/DE13/DE14 STAND/1x500/2x500/3x500 SHEET PAPER DRAWER

Get Sharp MX-2310U PDF manuals and user guides View all Sharp MX-2310U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

F. Image off-center adjustment The image lead edge position and the off-center adjustment value of the desk unit have been set to the average value when shipping from the factory. Therefore, this adjustment must be performed only when the judgment is made to execute it through checking the print image. 1) Enter the SIM50-28 mode. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&( 2&ǂ$'63)ǂ$'- 5(68/7 %.0$*ǂ$'6(78335,17ǂ$'- '$7$  &/26( 5) Press [EXECUTE] key. The patch image (adjustment pattern) is printed out. 6) Set the adjustment pattern on the document table. Fit the adjustment pattern correctly with the document guide. In this case, put 5 sheets of white paper on the printed adjustment pattern. 2) Select [SETUP/PRINT] ADJ with the key button. 3) Select [ALL] with the key button. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&( /($' $// 2))6(7   &/26( 7) Press [EXECUTE] key. The following item is automatically adjustment. • Print image lead edge image position adjustment • Print image off-center adjustment 8) Press [OK] key. The adjustment result becomes valid. Perform procedures 4) to 7) for each paper feed tray.  By pressing [LEAD] or [OFFSET] button, the following items can be executed individually. • [LEAD]: Print image lead edge image position adjustment • [OFFSET]: Print image off-center adjustment When [ALL] is selected, both of the above two items are executed simultaneously. 4) Select a paper feed tray to be adjusted. ǂ7(ǂ6ǂ7 6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&( 0)7 &6 &6 &6 &6 /&&  &/26( $'8 (;(&87(  MX-2310U MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 - 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
MX-2310U
MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER)
4
– 4
F.
Image off-center adjustment
The image lead edge position and the off-center adjustment value
of the desk unit have been set to the average value when shipping
from the factory.
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.
1)
Enter the SIM50-28 mode.
2)
Select [SETUP/PRINT] ADJ with the key button.
3)
Select [ALL] with the key button.
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
•
[LEAD]: Print image lead edge image position adjustment
•
[OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
4)
Select a paper feed tray to be adjusted.
5)
Press [EXECUTE] key.
The patch image (adjustment pattern) is printed out.
6)
Set the adjustment pattern on the document table.
Fit the adjustment pattern correctly with the document guide.
In this case, put 5 sheets of white paper on the printed adjust-
ment pattern.
7)
Press [EXECUTE] key.
The following item is automatically adjustment.
•
Print image lead edge image position adjustment
•
Print image off-center adjustment
8)
Press [OK] key.
The adjustment result becomes valid.
Perform procedures 4) to 7) for each paper feed tray.