Sharp MX-2310U Installation Manual - Page 32

Installation of the table glass, External fitting attachment, all movable area.

Get Sharp MX-2310U PDF manuals and user guides View all Sharp MX-2310U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

2) Remove two screws from the scanner bottom. 6) Move the lamp unit by hand and check that it move smoothly in all movable area. Check that there is no interference of the harness of the scanner heater in the wire and the 2/3 mirror unit. 3) Connect the harness of the scanner heater. Install the scanner heater unit, and fixing the screw (M3 x 4 Round-tipped). 2 2 1 4) Install the scanner heater and secure it with the screw (M4 x 6 Bind machine screw). Pass the harness through the clamp. The convex part of the scanner heater must be inserted into the hole of the scanner frame. (6) Installation of the table glass 1) Install the SPF glass and the table glass. Install the glass holder. When installing the glass holder, slide it to the left until it clicks, and fix it with screws. 1 2 3 12 54 (7) External fitting attachment 1) Attach the rear cabinet. 5) Tighten the loose scanner heater harness by pulling it in the arrow direction and secure it with the snap band then cut its tip to approx. 5 mm or less. 2 1 2 2 2 2 MX-2310U Dehumidifying heater 3 - 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
MX-2310U
Dehumidifying heater
3 – 9
2)
Remove two screws from the scanner bottom.
3)
Connect the harness of the scanner heater. Install the scanner
heater unit, and fixing the screw (M3 x 4 Round-tipped).
4)
Install the scanner heater and secure it with the screw (M4 x 6
Bind machine screw). Pass the harness through the clamp.
The convex part of the scanner heater must be inserted into
the hole of the scanner frame.
5)
Tighten the loose scanner heater harness by pulling it in the
arrow direction and secure it with the snap band then cut its tip
to approx. 5 mm or less.
6)
Move the lamp unit by hand and check that it move smoothly in
all movable area.
Check that there is no interference of the harness of the scan-
ner heater in the wire and the 2/3 mirror unit.
(6)
Installation of the table glass
1)
Install the SPF glass and the table glass. Install the glass
holder.
When installing the glass holder, slide it to the left until it clicks,
and fix it with screws.
(7)
External fitting attachment
1)
Attach the rear cabinet.
2
2
1
1
2
5
2
1
4
3
1
2
2
2
2
2