Sharp MX-2310U Installation Manual - Page 31

Assembling of the scanner heater unit, Removal of the table glass

Get Sharp MX-2310U PDF manuals and user guides View all Sharp MX-2310U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

3) Hang the SCN-WH harness to the main drive unit. 3) Tighten the snap band and cut its tip to approx. 5 mm or less. Slide the banding band head to the square hole (Part that is enclosed by the mark). The banding band head and cut tip must not protrude behind the heater fixing plate. 4) Connect the SCN-WH harness to the WH PWB. (3) Assembling of the scanner heater unit 1) Secure the marking position on the harness of the scanner heater to the heater fixing plate with the banding band. 3 2 1 (4) Removal of the table glass 1) Remove the glass holder. Remove the table glass and the SPF glass. 5 4 3 12 2) Extend the harness, and secure the other position of it with banding band. (5) Installation of the scanner heater unit 1) Attach the clamp to the scanner frame. When installing, be careful to prevent damage of the wire. MX-2310U Dehumidifying heater 3 - 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
MX-2310U
Dehumidifying heater
3 – 8
3)
Hang the SCN-WH harness to the main drive unit.
4)
Connect the SCN-WH harness to the WH PWB.
(3)
Assembling of the scanner heater unit
1)
Secure the marking position on the harness of the scanner
heater to the heater fixing plate with the banding band.
2)
Extend the harness, and secure the other position of it with
banding band.
3)
Tighten the snap band and cut its tip to approx. 5 mm or less.
Slide the banding band head to the square hole (Part that is
enclosed by the mark).
The banding band head and cut tip must not protrude behind
the heater fixing plate.
(4)
Removal of the table glass
1)
Remove the glass holder. Remove the table glass and the
SPF glass.
(5)
Installation of the scanner heater unit
1)
Attach the clamp to the scanner frame.
When installing, be careful to prevent damage of the wire.
1
2
3
1
4
5
2
3