Sharp MX-2310U Installation Manual - Page 17

Copy color balance and density check, Method 1

Get Sharp MX-2310U PDF manuals and user guides View all Sharp MX-2310U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

5) If the display of ALL_ROTATE is NG, turn all the LSU skew adjustment screws to adjust, and perform the procedures 2) to 4). Repeat the procedures 2) to 5) until the display of ALL_ROTATE becomes OK. If the display of ALL_ROTATE is OK, go to the procedure 6). For the adjustment, remove the front cover and the waste toner box, and turn the skew adjustment screw. 6) Repeat the procedures 2) to 4) again, and check to confirm that C, M, and Y (SKEW) are OK. If any of them is NG, turn the LSU skew adjustment screw of the corresponding color to adjust. (2) Copy color balance and density check Before checking the copy color balance and density, be sure to execute the following jobs. * Execute the high density image correction (Process correction) forcibly. (SIM 44-6) * Execute the half-tone image correction forcibly. (SIM 44-26) Method 1 Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy of the servicing color test chart (UKOG-0326FCZZ/UKOG0326FC11), and check that they are proper. a. Note for execution of the color balance and density check in the color copy mode To check the copy color balance and density, use the gray test chart (UKOG-0162FCZZ) and the servicing color test chart (UKOG-0326FCZZ/UKOG-0326FC11). Set the copy density level to "3" in the Text/Printed Photo mode (Manual), and make a copy. At that time, all the color balance adjustments in the user adjustment mode must be set to the default (center). In addition, be sure to use the specified paper for color. b. Note for checking the monochrome copy mode density To check the density, use the gray test chart (UKOG-0162FCZZ). Set the copy density level to "Manual 3" in the Text/Printed Photo mode (Manual). In addition, all the color balance adjustments in the user adjustment mode must be set to the default (center). [Check with the gray test chart (UKOG-0162FCZZ)] In the copy density check with the gray test chart, check to insure the following conditions. For the color (gray) balance, use the servicing color test chart (UKOG-0326FCZZ/UKOG-0326FC11) to check. (Color copy) Patch 1 is slightly copied. SHARP gray chart SHARP GRAY CHART 1 2 3 4 5 6 7 8 9 10 W Patch 2 is copied. ( py) Patch 2 is slightly copied. SHARP gray chart SHARP GRAY CHART 1 2 3 4 5 6 7 8 9 10 W When the adjustment is made by turning the LSU skew adjustment screw of K, the states of C, M and Y (SKEW) are changed. Execute SIM50-22 to check to confirm that C, M, and Y (SKEW) are OK. When an abnormality occurs, "ERROR" is displayed. In this case, check each drive section and the process section. Patch 3 is copied. Patch 1 is not copied. [Check with the servicing color test chart (UKOG-0326FCZZ/ UKOG-0326FC11)] In the copy color balance check with the servicing color test chart, check to insure the following conditions. (Color copy) Serviceman chart (Color patch section) The densities of patches 1 - 6 of each color are properly balanced. MX-2310U MX-2310U (MAIN UNIT) 2 - 8 Patch 7 is slightly copied or not copied.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
MX-2310U
MX-2310U (MAIN UNIT)
2 – 8
5)
If the display of ALL_ROTATE is NG, turn all the LSU skew
adjustment screws to adjust, and perform the procedures 2) to
4).
Repeat the procedures 2) to 5) until the display of
ALL_ROTATE becomes OK. If the display of ALL_ROTATE is
OK, go to the procedure 6).
For the adjustment, remove the front cover and the waste
toner box, and turn the skew adjustment screw.
6)
Repeat the procedures 2) to 4) again, and check to confirm
that C, M, and Y (SKEW) are OK.
If any of them is NG, turn the LSU skew adjustment screw of
the corresponding color to adjust.
When the adjustment is made by turning the LSU skew adjustment
screw of K, the states of C, M and Y (SKEW) are changed. Execute
SIM50-22 to check to confirm that C, M, and Y (SKEW) are OK.
When an abnormality occurs, "ERROR" is displayed.
In this case, check each drive section and the process section.
(2)
Copy color balance and density check
Before checking the copy color balance and density, be sure to
execute the following jobs.
*
Execute the high density image correction (Process correction)
forcibly. (SIM 44-6)
*
Execute the half-tone image correction forcibly. (SIM 44-26)
Method 1
Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy
of the servicing color test chart (UKOG-0326FCZZ/UKOG-
0326FC11), and check that they are proper.
a. Note for execution of the color balance and density check in the
color copy mode
To check the copy color balance and density, use the gray test
chart (UKOG-0162FCZZ) and the servicing color test chart
(UKOG-0326FCZZ/UKOG-0326FC11). Set the copy density
level to "3" in the Text/Printed Photo mode (Manual), and make a
copy.
At that time, all the color balance adjustments in the user adjust-
ment mode must be set to the default (center).
In addition, be sure to use the specified paper for color.
b. Note for checking the monochrome copy mode density
To check the density, use the gray test chart (UKOG-0162FCZZ).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).
In addition, all the color balance adjustments in the user adjust-
ment mode must be set to the default (center).
[Check with the gray test chart (UKOG-0162FCZZ)]
In the copy density check with the gray test chart, check to insure
the following conditions.
For the color (gray) balance, use the servicing color test chart
(UKOG-0326FCZZ/UKOG-0326FC11) to check.
[Check with the servicing color test chart (UKOG-0326FCZZ/
UKOG-0326FC11)]
In the copy color balance check with the servicing color test chart,
check to insure the following conditions.
1
2
3
4
5
6
7
8
9
10
W
SHARP
GRAY CHART
SHARP gray chart
Patch 1 is
slightly copied.
Patch 2 is copied.
(Color copy)
1
2
3
4
5
6
7
8
9
10
W
SHARP
GRAY CHART
SHARP gray chart
Patch 1 is not copied.
Patch 2 is
slightly copied.
Patch 3 is copied.
Serviceman chart (Color patch section)
The densities of patches 1 - 6 of
each color are properly balanced.
Patch 7 is slightly
copied or not copied.
(Color copy)