Sony PXW-Z190 Operating Instructions - Page 148

Error/Warning Indications, Error indications

Get Sony PXW-Z190 PDF manuals and user guides View all Sony PXW-Z190 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Error/Warning Indications The camcorder informs you of situations where warning, caution, or an operation check is required, through messages on the viewfinder screen, the recording/tally lamp, and a buzzer. The warning sound is emitted from the built-in speaker and headphones connected to the headphone connector. Error indications The camcorder will stop operation when the following kind of display occurs. Error indication on Warning Recording/ LCD/viewfinder sound tally lamp E + error code Intermittent High-speed flashing Cause and Solution Indicates an abnormality in the camcorder. Recording stops, even if "zRec" is displayed in the viewfinder. Turn off the camcorder, and check for any problem with connected devices, cables, or media. If the error persists when the camcorder is turned on again, contact your Sony service representative. (If power cannot be turned off by setting the ON/STANDBY switch to STANDBY, remove the battery pack and/or the DC IN source.) An error or warning may not be displayed depending on the status of the camcorder. Warning indications Follow the instructions provided if the following display occurs. Warning indication on LCD/viewfinder Battery Near End Battery End Temperature High Voltage Low Insufficient Voltage Media Near Full Media Full Warning Recording/ Cause and Solution sound tally lamp Intermittent Flashing The remaining capacity of the battery pack is getting low. Recharge at the earliest convenience. Continuous High-speed flashing The battery pack is empty. Recording cannot be performed. Stop operation and replace the battery pack. Intermittent Flashing The internal temperature is high. Turn off the camcorder and allow it to cool down before operating it again. Intermittent Flashing The DC IN voltage is low (level 1). Check the power supply. Continuous High-speed The DC IN voltage is too low (level 2). Recording flashing cannot be performed. Connect a different power source. Intermittent Flashing Free space on the memory card has become insufficient. Replace at the earliest convenience. Continuous High-speed No space is left on the memory card. Recording, flashing clip copying and clip division cannot be performed. Replace immediately. 148

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
148
The camcorder informs you of situations where warning, caution, or an operation check is required,
through messages on the viewfinder screen, the recording/tally lamp, and a buzzer.
The warning sound is emitted from the built-in speaker and headphones connected to the headphone
connector.
The camcorder will stop operation when the following kind of display occurs.
Follow the instructions provided if the following display occurs.
Error/Warning Indications
Error indications
Error indication on
LCD/viewfinder
Warning
sound
Recording/
tally lamp
Cause and Solution
E + error code
Intermittent
High-speed
flashing
Indicates an abnormality in the camcorder. Recording stops,
even if “
z
Rec” is displayed in the viewfinder.
Turn off the camcorder, and check for any problem with
connected devices, cables, or media. If the error persists when
the camcorder is turned on again, contact your Sony service
representative.
(If power cannot be turned off by setting the ON/STANDBY
switch to STANDBY, remove the battery pack and/or the DC
IN source.)
An error or warning may not be displayed depending on the
status of the camcorder.
Warning indications
Warning indication on
LCD/viewfinder
Warning
sound
Recording/
tally lamp
Cause and Solution
Battery Near End
Intermittent
Flashing
The remaining capacity of the battery pack is
getting low.
Recharge at the earliest convenience.
Battery End
Continuous
High-speed
flashing
The battery pack is empty. Recording cannot be
performed.
Stop operation and replace the battery pack.
Temperature High
Intermittent
Flashing
The internal temperature is high.
Turn off the camcorder and allow it to cool down
before operating it again.
Voltage Low
Intermittent
Flashing
The DC IN voltage is low (level 1). Check the
power supply.
Insufficient Voltage
Continuous
High-speed
flashing
The DC IN voltage is too low (level 2). Recording
cannot be performed.
Connect a different power source.
Media Near Full
Intermittent
Flashing
Free space on the memory card has become
insufficient.
Replace at the earliest convenience.
Media Full
Continuous
High-speed
flashing
No space is left on the memory card. Recording,
clip copying and clip division cannot be performed.
Replace immediately.