Sony PXW-Z190 Operating Instructions - Page 61

Setting the network client mode, connection, Set Network Client Mode >Setting

Get Sony PXW-Z190 PDF manuals and user guides View all Sony PXW-Z190 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Control Manager (CCM) or connecting via XDCAM air. Using network client mode, you can also conduct intercom calls between the camcorder and a Network RX Station CCM or XDCAM air using a headset connected to the USB 3.0 (HOST) connector of the camcorder. Setting the network client mode connection Up to three network client mode connections can be configured as NCM Settings. 1 Select Network Client Mode >NCM Settings1 (or NCM Settings2, NCM Settings3) in the Network menu. The network client mode connection destination setup screen appears. 2 Set each item on the connection destination setup screen. Display Name Set the display name in the NCM Settings menu. CCM Address Enter the address of the CCM to connect (host name or IP address). CCM Port Enter the port number of the CCM to connect. User Name Enter the user name. Password Enter the password. CCM Certificate Configure the certificate for CCM and XDCAM air connection. • Load Select Set in step 3, and import a certificate. * The certificate to be loaded must be in PEM format, and should be written to the root directory of the SD card with "CCM_certification.pem" file name. • Clear Select Set in step 3, and clear a certificate. • None Do not load or clear a certificate. Notes • Set the clock of the camcorder to the correct time before loading CCM and XDCAM air connection certificates. • In low voltage state, CCM and XDCAM air connection certificates cannot be loaded or cleared. CCM Certificate Status Displays the load status of the certificate. Camera Control Enable/disable camera control when connected with a CCM. Camera Setting Enable/disable ALL file operations when connected with a CCM. Reset Reset the settings of NCM Settings to the defaults. 3 When finished, select Set to apply the settings. Always select Set after changing the settings. The settings are not applied if Set is not selected. 4 Select Network Client Mode >NCM Settings Select in the Network menu, and then select the NCM settings (NCM Settings1, NCM Settings2, NCM Settings3) specified in steps 1 to 3. Connecting in network client mode 1 Connect the camcorder to the Internet as described in "Connecting to the Internet" (page 54). 2 Set Network Client Mode >Setting in the Network menu to On. Network client mode is enabled, and the camcorder connects to the Network RX Station or XDCAM air. Live streaming starts in response to Network RX Station operation. For details about operation, refer to the instruction manual for the Network RX Station or the Help for XDCAM air. You can also set Setting to On or Off by pressing an assignable button (page 38) assigned with Network Client Mode. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
61
Control Manager (CCM) or connecting via
XDCAM air.
Using network client mode, you can also conduct
intercom calls between the camcorder and a
Network RX Station CCM or XDCAM air using
a headset connected to the USB 3.0 (HOST)
connector of the camcorder.
Setting the network client mode
connection
Up to three network client mode connections can
be configured as NCM Settings.
1
Select Network Client Mode >NCM
Settings1 (or NCM Settings2, NCM
Settings3) in the Network menu.
The network client mode connection
destination setup screen appears.
2
Set each item on the connection
destination setup screen.
Display Name
Set the display name in the NCM Settings
menu.
CCM Address
Enter the address of the CCM to connect
(host name or IP address).
CCM Port
Enter the port number of the CCM to
connect.
User Name
Enter the user name.
Password
Enter the password.
CCM Certificate
Configure the certificate for CCM and
XDCAM air connection.
• Load
Select Set in step 3, and import a certificate.
* The certificate to be loaded must be in PEM
format, and should be written to the root
directory of the SD card with
“CCM_certification.pem” file name.
• Clear
Select Set in step 3, and clear a certificate.
• None
Do not load or clear a certificate.
Notes
•
Set the clock of the camcorder to the correct time
before loading CCM and XDCAM air connection
certificates.
•
In low voltage state, CCM and XDCAM air
connection certificates cannot be loaded or
cleared.
CCM Certificate Status
Displays the load status of the certificate.
Camera Control
Enable/disable camera control when
connected with a CCM.
Camera Setting
Enable/disable ALL file operations when
connected with a CCM.
Reset
Reset the settings of NCM Settings to the
defaults.
3
When finished, select Set to apply the
settings.
Always select Set after changing the settings.
The settings are not applied if Set is not
selected.
4
Select Network Client Mode >NCM
Settings Select in the Network menu,
and then select the NCM settings (NCM
Settings1, NCM Settings2, NCM
Settings3) specified in steps 1 to 3.
Connecting in network client mode
1
Connect the camcorder to the Internet
as described in
“Connecting to the
Internet” (page 54)
.
2
Set Network Client Mode >Setting in
the Network menu to On.
Network client mode is enabled, and the
camcorder connects to the Network RX
Station or XDCAM air.
Live streaming starts in response to Network
RX Station operation. For details about
operation, refer to the instruction manual for
the Network RX Station or the Help for
XDCAM air.
You can also set Setting to On or Off by
pressing an assignable button
(page 38)
assigned with Network Client Mode.