Sony SDM-N80 Operating Instructions (primary manual) - Page 26

Self-diagnosis function This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard or moving the mouse. 1 (power) indicator If the 1 (power) indicator is green 1 Turn off the AC power switch and disconnect the video signal cables from the INPUT1 and INPUT2 connectors of the media engine. 2 Press the AC power switch twice to turn the monitor off and then on. If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s). If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor's condition. If the 1 (power) indicator is flashing orange Press the 1 (power) switch twice to turn the display off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor's condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and graphics board. Specifications LCD panel Input signal format Resolution** Video input connector Input signal levels Audio output Headphones jack AUDIO IN jacks Power requirements Power consumption Operating temperature Dimensions (w/h/d) Mass Plug & Play Accessories Panel type: a-Si TFT Active Matrix Picture size: 18.1 inch (46 cm) RGB operating frequency* Horizontal: 28 - 92 kHz** Vertical: 48 - 85 Hz** Horizontal: Max.1280 dots Vertical: Max.1024 lines Analog RGB: HD15 Digital/analog RGB: DVI-I 29 pins Analog RGB video signal 0.700 Vp-p, 75 Ω, positive SYNC signal TTL level, 2 kΩ, positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75 Ω, negative (Sync on green) Digital RGB (DVI) video signal TMDS (Single link) 1W×2 Stereo minijack Accepts impedance of 16 - 48 Ω Stereo minijack × 2 Accepts impedance of 47 kΩ Accepts level 0.5 Vrms 100 - 240 V, 50 - 60 Hz, 0.7 - 0.4 A Max. 67 W 5 - 35 °C Display (upright and in the lowest position): Approx. 432 × 400 × 195 mm (17 1/8 × 15 3/4 × 7 3/4 inches) Media engine: Approx. 94 × 212 × 204 mm (3 3/4 × 8 3/8 × 8 1/8 inches) Display: Approx. 6.5 kg (14 lb 5 oz) Media engine: Approx. 1.5 kg (3 lb 5 oz) DDC2B See page 7. * Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.5 µsec. • Vertical blanking width should be more than 450 µsec. **A 1600 × 1200 resolution signal is displayed provisionally as long as its horizontal and vertical frequencies are lower than the following values. • Analog RGB signal: Horizontal 107 kHz, Vertical 85 Hz • Digital RGB signal: Horizontal 75 kHz, Vertical 60 Hz Design and specifications are subject to change without notice. 26