TRENDnet TPE-1620WS User's Guide - Page 38

Set Ingress Rate Limiting

Get TRENDnet TPE-1620WS PDF manuals and user guides View all TRENDnet TPE-1620WS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

TRENDnet User's Guide Set Ingress Rate Limiting Bridge > Bandwidth Control > Ingress Rate Limiting This section allows you to set the ingress (receive) rate for each switch port. 1. Log into your switch management page (see "Access your switch management page" on page 11). 2. Click on Bridge, click on Bandwidth Control, and click on Ingress Rate Limiting. 3. Review the settings for each port. Click Apply to save the settings. • Bandwidth - Enter the ingress rate limit value. • Status - Click the drop-down list and select Enabled to enable ingress rate limiting or select Disabled to disable ingress rate limiting. Note: Modifying settings in the row marked All, will apply the settings to all ports. TPE-1620WS Set Egress Rate Limiting Bridge > Bandwidth Control > Egress Rate Limiting This section allows you to set the egress (transmit) rate for each switch port. 1. Log into your switch management page (see "Access your switch management page" on page 11). 2. Click on Bridge, click on Bandwidth Control, and click on Egress Rate Limiting. 3. Review the settings for each port. Click Apply to save the settings. • Bandwidth - Enter the egress rate limit value. • Status - Click the drop-down list and select Enabled to enable egress rate limiting or select Disabled to disable egress rate limiting. Note: Modifying settings in the row marked All, will apply the settings to all ports. 4. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. 4. Click Save Settings to Flash (menu). 5. Click Save Settings to Flash (button), then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. © Copyright 2013 TRENDnet. All Rights Reserved. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-1620WS
38
Set Ingress Rate Limiting
Bridge > Bandwidth Control > Ingress Rate Limiting
This section allows you to set the ingress (receive) rate for each switch port.
1. Log into your switch management page (see “
Access your switch management page
”
on page 11).
2. Click on
Bridge
, click on
Bandwidth Control,
and click on
Ingress Rate Limiting
.
3. Review the settings for each port. Click
Apply
to save the settings.
•
Bandwidth
– Enter the ingress rate limit value.
•
Status
– Click the drop-down list and select
Enabled
to enable ingress rate
limiting or select
Disabled
to disable ingress rate limiting.
Note:
Modifying settings in the row marked
All
, will apply the settings to all
ports.
4. Click
Save Settings to Flash (menu)
.
5. Click
Save Settings to Flash (button)
, then click
OK.
Note:
This step saves all configuration changes to the NV-RAM to ensure that if the
switch is rebooted or power cycled, the configuration changes will still be applied.
Set Egress Rate Limiting
Bridge > Bandwidth Control > Egress Rate Limiting
This section allows you to set the egress (transmit) rate for each switch port.
1. Log into your switch management page (see “
Access your switch management page
”
on page 11).
2. Click on
Bridge
, click on
Bandwidth Control,
and click on
Egress Rate Limiting
.
3. Review the settings for each port. Click
Apply
to save the settings.
•
Bandwidth
– Enter the egress rate limit value.
•
Status
– Click the drop-down list and select
Enabled
to enable egress rate
limiting or select
Disabled
to disable egress rate limiting.
Note:
Modifying settings in the row marked
All
, will apply the settings to all
ports.
4. Click
Save Settings to Flash (menu)
.
5. Click
Save Settings to Flash (button)
, then click
OK.
Note:
This step saves all configuration changes to the NV-RAM to ensure that if the
switch is rebooted or power cycled, the configuration changes will still be applied.